background image

                                

SERVICE     2 

 AQUATECH   OPERATIONS,  SERVICE   AND   PARTS   MANUAL 

A Product of Hi-Vac Corporation

SERVICE

  

 

LIMITED WARRANTY 

Hi-Vac® Corporation (the "Company") hereby warrants to  that each new  X-VAC® Hydro Excavator (the "Unit") will be free of defects in 

material and workmanship.  This Limited Warranty applies to the original end user and any transferee during the applicable time period, 

subject to the following terms and conditions:

 

 

 

1. Time Periods:     

  The  "Standard Warranty Period" is 12 months from date of 

delivery to the original end user or 2,000 operating hours, 

whichever occurs first.  Any Unit which has been used as a 

demonstration unit will, upon sale and delivery to the end  user, 

have the same Limited Warranty as provided for herein.   

  Special Extended Warranties and Extended Time Periods:  

 

(a)  Poly-graphite Tanks Warranty: 10 years against any factory 

defect in material or workmanship and LIFETIME against 

leakage from corrosion or rust through. 

 

(b)  Debris Tanks Warranty: 10 years against any factory defect 

in material and LIFETIME  against leaks due to corrosion or 

rust through. 

 

(c)  Water  Pump Warranty:  5  years against water pump failure  

and/or 

factory defect in material or workmanship. 

 

(d)  Drive  System:  5  years against 

drive  system  failure  and/or 

any factory defect in material or workmanship.  The  Drive 

System warranty is non-transferrable 

 

2. Exclusive Remedy: The exclusive remedy for any covered warranty 

claims is that Company shall repair or replace, or in lieu thereof may 

refund the purchase price, at is sole discretion, such defects of such 

Unit  that the Company's examination discloses to be defective in 

material or factory workmanship, at Company's sole discretion.  Any 

repairs or replacements are to be made at a location approved by 

Company (i.e. a selling distributor's location or the Company's facility) 

to assure the Unit performs according  to its published specifications.  

 

3  The Following Limitations Apply:  

(a)  This Limited Warranty applies only to the original end user 

during the applicable warranty time periods.   

(b)  Only a Unit  which has  been subjected to normal use and 

preventative maintenance per original Manufacturer 

recommendations contained in the Operator's Manuel delivered 

with the Unit is covered by this Limited Warranty.  

(c)  This Limited Warranty shall not apply to (and the Company shall 

not be responsible for) any of the following: 

  items or parts of the Unit  that are subject to misuse, 

negligence, accident or improper maintenance by end user. 

  normal  maintenance  and service  adjustments,  including, but 

not limited to engine valve adjustments, fuel, air and hydraulic 

system cleaning, engine tune-up, clutch inspection and 

adjustment, etc. 

  standard consumables and preventative maintenance items 

or  normal  wear parts such as, but not limited to:  oils, fluids, 

lubricants, hoses, gaskets, fuses, light bulbs, tires, batteries, 

belts, etc. 

  operation of the Unit  in  a  manner or for a purpose not 

specifically recommended in writing by the Company. 

  repairs, modifications or alterations without the express 

written consent of the Company, which in the Company's sole 

judgment, have adversely affected the Unit's operation, 

stability,  or functionality as originally designed and 

manufactured by Company. 

(d)  The  Unit  and supporting equipment may incorporate many 

component parts manufactured by companies other than 

Manufacturer; including, but not limited to the following: the truck 

chassis, engines, compressors, 

water pump, exhauster/

vacuum 

pump, high pressure water hose, hydraulic pumps, motors and 

valves, batteries, drive belts, power take-off,  axels, tires, 

electrical components and other specialized equipment. This 

Limited  Warranty  does not apply to such component parts or 

sub-systems. For equipment and components mentioned in this 

section, the end user will address warranty service and support 

direct with the original manufacturer or nearest authorized 

servicing distributor  for such component parts or sub-systems.  

While this Limited Warranty does not cover component parts and 

sub-systems manufactured by third parties, Company shall 

pass-through to end user any warranties (if any) from such 

component or sub-system manufacturer to the extent permitted 

and  simply as a matter of customer service shall make good 

faith efforts to provide any relevant information or reasonable 

assistance to end user/purchaser 

related to contacting such third 

party vendors regarding their warranties.  

(e)  Any repair or replacement made to replace any defects in 

material or workmanship of the Unit is warranted solely for the 

duration of the unexpired Warranty  Period.

 

No extension of 

warranty is made by installation of the new part. 

(f)  Company  reserves the right to request the return of failed or 

defective parts or components to Company's  factory origin for 

evaluation  subject to Company's return authorization process 

and procedure. 

(g)  Company  will not be responsible or liable for defects, losses, 

damages or failures caused by end user's (or any third party's) 

unauthorized alternations, use of non-approved parts, 

unreasonable use, neglect, abuse, accident, negligent repair or 

failure to perform proper maintenance. 

(h)  It is the responsibility of the end user to report warranty claims in 

a timely manner. Damages resulting from failure to report such 

claims promptly are not covered under this warranty. 

(i)  The term "LIFETIME" means and applies to the original end user 

only and covers only the original end user's ownership period. 

 

4. No Other Warranties. There are no other warranties made by 

company with respect to the Units, expressed or implied, other than 

the limited warranty as set forth above. This limited warranty 

supersedes any other warranty, promises or representations previously 

made or issued by company.  THIS WARRANTY IS IN LIEU OF ALL 

OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT 

NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY OR 

FITNESS FOR A PARTICULAR PURPOSE AND COMPANY HEREBY 

EXCLUDES ALL SUCH WARRANTIES WHICH MIGHT OTHERWISE 

BE IMPLIED BY LAW, ALL OF WHICH ARE HEREBY DISCLAIMED. 

The Company makes no representation that the Unit has the capacity 

to perform any functions other than as contained in the Company's 

written literature, specifications or Owner's Manual accompanying 

delivery of the Unit.  No person, affiliated company or distributor of 

Company's products, is authorized to alter the terms of this warranty, 

to give any other warranties or to assume any other liability on behalf 

of the Company in connection with the sale, servicing or repair of any 

Unit manufactured by the Company. 

 

5. 

Design  Changes/Product  Improvements

.  The Company reserves 

the right to make design changes or improvements in its products from 

time to time without any obligation to change or improve any previously 

manufactured Units.  

 

6.  Limitation of Liability.  Company's liability for breach of this Limited 

Warranty, whether a claim or lawsuit is brought in contract, tort, or 

strict liability, will be limited exclusively to repair or replacement of 

defects covered by the terms of this Limited Warranty.  Company will 

not be liable for any direct or indirect, incidental, consequential, special 

or punitive damages of any kind which may result from defects in its 

Units, products, services, or from breach of this Limited Warranty, nor 

will Company 

be liable for any damages resulting from the end user’s 

loss of use of the Unit 

and/or its supporting equipment.

 

 

Summary of Contents for X-Vac Hydro Excavator X15 Series
























































































Reviews: