background image

Rev. H 11-2021

46

MTEC.6800.GB-H-1 Operation and maintenance manual SMA series English

SMA

6ZLPPLQJSRROGHKXPLGL¿HUV

Site assembled refrigerant circuits must be assembled and maintained carefully, in order to prevent malfunctions.

Therefore:
• 

$YRLGRLOUHSOHQLVKPHQWZLWKSURGXFWVWKDWDUHGLIIHUHQWIURPWKDWVSHFL¿HGDQGWKDWDUHSUHORDGHGLQWRWKHFRPSUHVVRU

•  In the event of a gas leakage on machines using refrigerant R410A even if it is only a partial leak, do not top up. The entire charge must 

EHUHFRYHUHGWKHOHDNUHSDLUHGDQGDQHZUH¿JHUDQWFKDUJHZHLJKHGLQWRWKHFLUFXLW

•  When replacing any part of the refrigerant circuit, do not leave it exposed for more than 15 minutes.
• 

,WLVLPSRUWDQWZKHQUHSODFLQJDFRPSUHVVRUWKDWWKHWDVNEHFRPSOHWHGZLWKLQWKHWLPHVSHFL¿HGDERYHDIWHUUHPRYLQJWKHUXEEHUVHDOLQJ

caps.

•  When replacing the compressor following a burn out, it is advisable to wash the cooling system with appropriate products including a 

¿OWHUIRUDFLG

•  When under vacuum do not switch on the compressor.

5HIULJHUDQWFLUFXLWUHSDLU

For leak detection, the system should be charged with oxygen free nitrogen using a gas cylinder and suitable nitrogen pressure regulator, 

XQWLOEDUSUHVVXUHLVUHDFKHG$Q\OHDNDJHLVGHWHFWHGXVLQJDEXEEOHOHDN¿QGHU

If the refrigerant circuit is to be emptied, all the refrigerant must be recovered using the correct equipment by

VXLWDEO\TXDOL¿HGIJDVHQJLQHHUV

Never use oxygen instead of oxygen free nitrogen: explosions may occur.

Daily and monthly works may be carried out directly by the Owner of the system. All other works must be perfor-
med by authorised and trained personnel.

Any kind of cleaning whatsoever is forbidden before disconnecting the device from power supply by turning the 
master switch to the OFF position. It is forbidden to touch the device while barefooted or with wet or damp body 
parts.

:RUNVRQWKHFRROLQJOLQHPXVWEHFDUULHGRXWE\TXDOL¿HGDQGWUDLQHGWHFKQLFLDQVDVSURYLGHGE\ORFDOODZVDQG

regulations in force.

7.4.3 Compressors

Action to be performed 

Frequency

Monthly

Every 

2 months

Every 

6 months

Every

 year

Every

5 years

As neces-

sary

Visually inspect compressors 

X

Check noise and vibration level of the compressors 

X

Check the supply voltage of the compressors 

X

Check the compressors’ electrical connections

X

&KHFNRLOOHYHOLQWKHFRPSUHVVRUVXVLQJWKHRLO¿OOOHYHOLQGLFDWRULISUHVHQW

X

Check that the crankcase heaters are powered and working properly (if present)

X

Check the conditions of the compressors’ power cables and their tightness in 
the clamps

X

Before the start-up it is necessary to carry out all the operations described in the previous tables and make the 
necessary checks provided by the pre-start control module (valid for the italian market) to be requested to the 
service.

Summary of Contents for SMA 270

























































Reviews: