AMPLIFIER FEATURE DESCRIPTIONS
2
GLADIATOR AMPLIFIERS:
A
POWER
LED indicates the powered up and turned on condition.
Each model is capable of 4 & 2-Ohms stereo per channel, or 4-Ohms mono bridged operation except
All Hifonics amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit,
the mono amps which are capable of 4, 2 and 1-Ohm loads.
and amplifier DC faults indicated by the red “
PROTECT”
LED.
Tri-Mode operation with any stereo pair of amplifier channels is possible, as with all bridgeable
CAUTION: DO NOT OPERATE ANY AMPLIFIER BELOW THE INTENDED IMPEDANCE. YOU
amplifiers.
The input sensitivities for rated output powers are variable from 0.2V to 6V for the multi channel
WILL CAUSE DAMAGE TO THE AMPLIFIER THAT WILL NOT BE COVERED UNDER THE
amplifiers and 0.2V to 9V for the mono models.
WARRANTY PRINTED IN THE BACK OF THE MANUAL. 2 & 4 Channel amps are capable of 4
All crossovers are fully variable in their respective ranges.
and 2-Ohms wired stereo and 4-Ohms wired mono bridged. The mono amps are capable of 4, 2
Crossover filters are 12dB/Octave.
and 1-Ohm.
SUBSONIC:
Crossover filter from 15Hz to 35Hz.
LOW PASS:
Crossover filter from 30Hz to 250Hz.
LEVEL:
Adjusts the input sensitivity from 0.2 volts to 9 volts.
BASS EQ:
Adjustable bass boost from 0db to 10dB.
PHASE:
REMOTE:
This is the input jack for the remote Level control.
BALANCED INPUT:
LINE INPUT
: The line input accepts unbalanced (RCA) inputs from 0.2V to 9V.
LINE OUTPUT
: The line output passes through signal from the line inputs which allows you to daisy
chain multiple amplifiers from one signal.
The Phase Shift is fully adjustable from 0 to 180 degrees and this allows you to control time
alignment.
Accepts line level balanced input from 0.4v to 18v.
-The
LINE INPUT
signal is routed directly to the
LINE OUT
RCA jacks, and not affected by the
settings on the amplifier simplifying daisy chaining of amplifiers.
SUBSONIC:
Crossover filter from 15Hz to 35Hz.
LOW PASS:
Crossover filter from 30Hz to 250Hz.
LEVEL:
Adjusts the input sensitivity from 0.2 volts to 9 volts.
BASS EQ:
Adjustable bass boost from 0db to 10dB.
PHASE:
REMOTE:
This is the input jack for the remote Level control.
BALANCED INPUT:
LINE INPUT
: The line input accepts unbalanced (RCA) inputs from 0.2V to 9V.
LINE OUTPUT
: The line output passes through signal from the line inputs which allows you to daisy
chain multiple amplifiers from one signal.
The Phase Shift is fully adjustable from 0 to 180 degrees and this allows you to control time
alignment.
Accepts line level balanced input from 0.4v to 18v.
-The
LINE INPUT
signal is routed directly to the
LINE OUT
RCA jacks, and not affected by the
settings on the amplifier simplifying daisy chaining of amplifiers.
The BRE2500.1D is a linkable amplifier and features a
MASTER / SLAVE
selection switch and
IN /
OUT
RCA connection.
The mono amps are capable of 4, 2 & 1-Ohm loads.
Operating the amp below 1-Ohm can cause damage to the
amp not covered in the warranty.
The mono amps are capable of 4, 2 & 1-Ohm loads.
Operating the amp below 1-Ohm can cause damage to the
amp not covered in the warranty.
GLX1000.1D / GLX1400.1D / GLX1800.1D MONO BLOCK AMPLIFIERS
GLX2200.1D MONO BLOCK AMPLIFIERS
The 4 channel amps have the same features as the 2 channel models accept that there are 2 sets of
controls.
1 set for channels 1 & 2 and 1 set for channels 3 & 4.
In addition, the 4 channel models have a
Mode
switch which allows you to select 2 or 4 channel
operation. Switch to 2 channel if you only have 1 set of RCA’s in CH 1/2 and the unit will automatically
supply signal to channels 3/4. Select 4 channel if you are providing RCA’s to channels 1/2 and 3/4.
The
X-OVER
slide switch selects the internal crossover functions:
-The input signal is routed directly to the
LINE OUT
RCA jacks, regardless of the
X-OVER
setting
simplifying daisy chaining of amplifiers.
-HI:
Selects the built in
HI PASS
filter.
-FULL:
Bypasses all crossovers for full frequency range operation.
-LP/BP:
Selects the built in
LOW PASS
filter.
LINE INPUT
: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V.
LINE OUTPUT
: The line output passes through signal from the line inputs which allows you to daisy
chain multiple amplifiers from one signal.
HI PASS:
Variable low frequency cut off from 10Hz to 15kHz.
LOW PASS:
Variable high frequency cut off from 30Hz to 150Hz.
BASS EQ:
45Hz bass boost variable from 0dB to 10dB.
LEVEL:
Variable
LEVEL
(GAIN) control from 6.0V to 0.2V.
Note that the LOW PASS signal is MONO.
-In the LP/BP position, the HI PASS filter acts as a subsonic
filter.
-When the LP/BP mode is selected, a 0 to +10dB, at 45Hz,
BASS EQ is also switched in.
GLX60.4 / GLX100.4 4-CHANNEL AMPLIFIERS
CH1/2 CH3/4 REMOTE HI PASS CH1/2 X-OVER LOW PASS BASS EQ LEVEL POWER LINE OUTPUT
10Hz 15kHz 30Hz 150Hz 0dB 10dB 6.0V 0.2V
10Hz 15kHz 30Hz 150Hz 0dB 10dB 6.0V 0.2V
LINE INPUT MODE HI PASS CH3/4 X-OVER LOW PASS BASS EQ LEVEL
PROTECT
L
R
L
R
2CH 4CH
HI FULL LP/BP
HI FULL LP/BP
INPUT OUTPUT INPUT LEVEL PHASE REMOTE BASS EQ SONIC LOW PASS
L
L
R
R
SUB
POWER
PROTECT
BALANCED
9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz
INPUT OUTPUT INPUT LEVEL PHASE REMOTE BASS EQ SONIC LOW PASS
L
L
R
R
SUB
IN
OUT
POWER
PROTECT
OUTPUT
MASTER
INPUT
SLAVE
BALANCED
9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz
Summary of Contents for Gladiator GLX100.4
Page 1: ...GLX60 4 GLX100 4 GLX1000 1D GLX1400 1D GLX1800 1D GLX2200 1D ...
Page 12: ...10 ...
Page 16: ...PART A1011 ...
