background image

4

Thank you for choosing a wood heater from High Valley Stove.  Safe and e

  cient opera  on of your wood heater depends 

greatly on proper installa  on as outlined in this owner’s manual.  If this wood heater is not properly installed, a house 

fi

 re may result.  To reduce the risk of 

fi

 re follow all instruc  ons, cau  ons, and safety no  ces contained herein.  Installa-

 on must also meet all State and Local Code requirements and/or restric  ons.  Check with your local Building O

  cial, 

Fire O

  cial, or other Authority Having Jurisdic  on (AHJ) regarding the need to obtain a permit prior to installing a wood 

heater; and whether an inspec  on of the installa  on is required upon comple  on.  Understand that code requirements 
and follow-up inspec  on are not put in place to make the installa  on process more di

  cult.  Rather they are designed 

to help ensure your safety.  Don’t take shortcuts, use or allow makeshi   methods, or other compromises in the instal-
la  on.  Safety is paramount and the key to enjoying your new wood heater.  We strongly recommend installa  on by an 
experienced professional installer who has the specialized knowledge, tools, and equipment to complete the installa  on 
safely.  Look for an installer who is cer  

fi

 ed by the The Na  onal Fireplace Ins  tute (NFI) as a Woodstove Specialist or 

Master Hearth Professional (MHP) to have demonstrated their mastery of the knowledge required in all phases of safe 
woodstove installa  on, and of best current industry prac  ces.  Be sure to contact your insurance company to inquire 
whether they have addi  onal requirements.

BURN SOLID WOOD FUEL ONLY. 

 This wood 

heater is designed and approved for the burning of 
cord wood fuel only.  Burning any type of fuel oth-
er than cord wood in this wood heater is against all 
safety tes  ng and will void all warran  es.

DO NOT USE CHEMICALS OR FLUIDS TO 
START THE FIRE.

 

 

Never use gasoline, gasoline-

type lantern fuel, kerosene, charcoal lighter 

fl

 uid, or 

similar liquids to start or “freshen up” a 

fi

 re in this 

wood heater. Keep all such liquids well away from 
the heater at all   mes.  Storing these or other 

fl

 am-

mable liquids near a wood heater could cause a 

fi

 re.

DO NOT BURN GARBAGE OR FLAMMABLE 
FLUIDS SUCH AS GASOLINE, NAPHTHA OR 
ENGINE OIL.

  

Cord wood is the only fuel approved 

for use in this wood heater.

DO NOT CONNECT THIS UNIT TO A CHIMNEY 
FLUE SERVICING ANOTHER APPLIANCE.

DO NOT CONNECT A WOOD HEATER TO, OR 
USE IN CONJUNCTION WITH, ANY AIR DIS
TRIBUTION DUCTWORK UNLESS SPECIFICAL
LY APPROVED FOR SUCH INSTALLATIONS.

DO NOT OPERATE IN AN EXTREME MANNER 
AS TO OVER FIRE THE WOOD HEATER.

  If any 

part of the wood heater, the chimney, or the chim-
ney connector glows, you are over-

fi

 ring.  If over-

fi

 r-

ing occurs, close all combus  on air controls imme-
diately.  Over-

fi

 ring can cause damage to the wood 

heater and may cause a 

fi

 re.

HOT WHILE IN OPERATION.  KEEP CHILDREN, 
CLOTHING, AND FURNITURE WELL AWAY. 

 

CONTACT MAY CAUSE SKIN BURNS.

  

Observe 

all minimum clearances as listed in this manual. 

 

Maintain a 36” area around the wood heater to be 
kept free of combus  ble materials including furni-
ture and window treatments.  

DO NOT

 allow unat-

tended children in the area of an opera  ng  wood 
heater.

BURN DIRECTLY ON FIRE BRICKS.

  

Do not use 

grates, andirons, or other methods to support fuel. 

FUEL STORAGE.

  

Store bulk cord wood covered in 

a well ven  lated area to ensure that the wood fuel is 
dry as possible.  Do not store wood fuel within stove 
clearances or within the space needed for loading 
stove or ash removal. 

ASH DISPOSAL.

  Ashes should be placed in a steel 

container with a   ght-

fi

    ng lid and moved outdoors 

immediately. The closed container of ashes should be 
placed on a non-combus  ble 

fl

 oor or on the ground, 

well away from all combus  ble materials, pending 

fi

 nal disposal. If the ashes are disposed of by burial 

in soil or otherwise locally dispersed, they should be 
retained in the closed container un  l all cinders have 
thoroughly cooled. Other waste shall not be placed 
in this container.

CREOSOTE FORMATION & REMOVAL:

  Inspect 

chimney connector and chimney twice monthly, and 
clean if necessary.  Creosote accumula  on in the 
connector pipe, chimney, or 

fl

 ue lining  can create an 

extremely hot 

fi

 re if ignited.

S

 P

G

 S

 I

Summary of Contents for 1300





















Reviews: