30/36
4.6.2 Modify the technical parameter
1. At the technical parameter setting state,
is sequence increasing key,press this
key can do operation of added 1(sequence:0-99)
2.At the technical parameter setting state,
is sequence descending key,press this
key can do operation of minus 1(sequence :0-99).
3.
are parameter setting key at this state, press the key once,
parameter of corresponding bit adds 1(it will not continue if the parameter overflow after
adding );press
key to save the parameter after setting, press
key again to
return to the holding state .
4.7 Common parameter description
The parameters marked with *mean that they should re-power after amended.
(Unit: RPM; ms ; s ; hour )
Sequence
Function
parameter
Default
Setting
range
unit Parameter
description
P0 Pedal
slope
20
1~100
%
The bigger the slope is, the
larger the low-speed region is,
and the faster the speed change
is; the smaller the slope is, the
narrower the low-speed region
is, and the lower the speed
change is.
P1
Speed
proportion
8 1~8
Presser proportion of the
maximum speed of reverse
sewing. The maximum seed is
equally divided into eight parts,
current speed can be modified
through adjusting parts.
P2
System
minimum
speed
200 150~500
RPM
The minimum speed of machine
head when sewing.
P3
Maximum
speed of the
reverse
sewing
4000(lockstitch
series)
3000(double
needle series)
5500(overlock
stitch series)
150~5000
150~4000
150~7500
RPM
The maximum speed of machine
head at the reverse sewing.
P4
Fixed sewing
speed
3500(lockstitch
series)
3000(double
needle series)
200~4000
RPM
Sewing speed of fixed sewing
speed.
P5
Fore-tacking
sewing speed
1800 200~3000
RPM
Sewing
speed of fore-tacking.
P6
Back-tacking
sewing speed
1800
200~3000
RPM
Sewing speed of back-tacking.
Summary of Contents for HW762T
