5
English
Class
II
tool
Warning
Prohibited action
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package
contains the accessories listed on page 45.
Standard accessories are subject to change without notice.
APPLICATIONS
○
Cutting metal and stainless steel pipe.
○
Cutting various lumbers.
○
Cutting mild steel plates, aluminum plates, and copper
plates.
○
Cutting synthetic resins, such as phenol resin and vinyl
chloride.
For details refer to the section entitled “SELECTION OF
BLADES”.
SPECIFICATIONS
Voltage (by areas) *
(110 V, 120 V, 230 V,
240 V)
Power Input *
1100 W
Capacity
Mild Steel Pipe
O.D. 130 mm
Vinyl Chloride
Pipe
O.D. 130 mm
Wood
Depth 300 mm
Mild Steel Plate
Thickness 19 mm
No-Load Speed
0 – 3000 /min
Stroke
32 mm
Weight (without cord)
3.9 kg
* Be sure to check the nameplate on product as it is
subject to change by areas.
NOTE
Due to HiKOKI’s continuing program of research and
development, the speci
fi
cations herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action
Figure
Page
Switch Operation
2
40
Adjusting operating speed*
1
3
41
Adjusting stroke
4
41
Mounting the blade
5
41
Dismounting the blade*
2
6
42
When the blade broken*
3
7
42
Adjusting the base
8
42
How to use the hook*
4
9
42
Select a saw blade of the
appropriate length
10
43
Fastening work piece
fi
rmly
11
43
Plunge cutting (for wood)
12
43
Plunge cutting with the saw blade
installed in reverse
13
44
Maintenance and inspection of
saw blade mount
14
44
Selecting accessories
―
46
Refer to
Table 1, 2
and
3
for use of the blades.
*1 Adjusting operating speed
CAUTION
Select mode while the trigger switch is released. Failure
to do so could result in malfunction.
Once you connect the power plug to an outlet and switch on
the power, you can change modes with each press of the
mode selector switch.
●
Speed change mode allows the number of maximum
strokes to be switched between 5 levels: minimum
speed, low speed, middle speed, high speed and Max.
speed.
With speed change mode, the set number of maximum
strokes will be maintained even if there is a change in
load.
Operating speed
Mode
Status
Operating speed
Transmisson
Mode
Min.
0 – 1200 /min
Low
0 – 1700 /min
Middle
0 – 2000 /min
High
0 – 2500 /min
Max.
0 – 3000 /min
*2 Dismounting the blade
CAUTION
Never touch the saw blade immediately after use. The
metal is hot and can easily burn your skin.
(1) After pivoting the lever, point the blade downward. The
blade should fall out on its own. If the blade fails to fall
out, pull it out by hand. (
Fig. 6
)
*3 When the blade is broken
Even when the saw blade is broken and remains inside
the small slit of the blade holder, it should fall out when
the lever is pivoted and the blade is pointed downward.
If the blade fails to fall out on its own, take it out by using
the procedures described below.
(1) If a part of the broken saw blade is sticking out of the
small slit of the blade holder, pull out the protruding part
and take the blade out.
(2) If the broken saw blade is hidden inside the small slit,
hook the broken blade using a tip of another saw blade
and take it out. (
Fig. 7
)
*4 How to use the Hook
The hook can be used to hang up the unit
temporarilyduring operations.
000Book̲CR13VEY̲Asia.indb 5
000Book̲CR13VEY̲Asia.indb 5
2019/03/06 9:35:51
2019/03/06 9:35:51
