11
English
○
When the pilot lamp
fl
ickers in red (at 0.2-seconds
intervals), check for and take out any foreign objects in
the charger’s battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
○
Since the built-in micro computer takes about 3 seconds
to con
fi
rm that the battery being charged with chargers
are taken out, wait for a minimum of 3 seconds before
reinserting it to continue charging. If the battery is
reinserted within 3 seconds, the battery may not be
properly charged.
MOUNTING AND OPERATION
Action
Figure
Page
Removing and inserting the battery
2
2
Charging
3
2
Indicator lamp lights when battery
is low
4
3
Installing/Removing the side
handle
5
3
Inserting SDS-plus drilling tools
6
3
Removing SDS-plus drilling tools
7
3
Selecting rotation direction
8
4
Selecting the operating mode
9
4
Adjusting the drilling depth
10
4
Switch operation
11
4
Setting the speed
12
4
Auto stop function
13
4
How to use the LED light
14
5
Cleaning the battery installation
compartment and the battery
15
5
Selecting accessories*
―
208, 209
* For detailed information regarding each tool, contact a
HiKOKI authorized service center.
SELECT OPERATION MODE
Pressing the changeover switch allows the selection of
rotation speed and the auto stop function.
○
Rotation speed (Low mode/Normal mode) (
Fig. 12
)
Select either Low mode or Normal mode and operate the
tool in the selected speed.
○
Auto stop mode (on/o
ff
) (
Fig. 13
)
This product is equipped with an auto stop function to
support continuous drilling work. The function features a
memory mode for storing the work time for drilling from
switch ON to switch OFF, and an auto stop mode that
automatically stops the motor from the second drilling
onward should the work exceed the stored work time
while the switch is ON.
AUTO STOP FUNCTION
In selection mode, pressing the button for longer than two
seconds will move to memory mode. (
Fig. 13
)
(At the same time the auto stop lamp will blink.)
Conduct drilling when the auto stop lamp is
fl
ashing. The
time between switching ON and switching OFF is stored by
the tool.
(At the same time, the auto stop lamp will light up.)
Conduct drilling when the auto stop lamp is
fl
ashing.
Continuous drilling is possible as the memory storage time
will be recorded by the tool until the auto stop function’s auto
stop mode is cancelled.
The auto stop function is cancelled by pressing the
changeover switch once again for over two seconds.
(At the same time, the auto stop lamp will switch o
ff
.)
CAUTION
○
Switch ON the tool once you place the tip of the tool on
the work material.
○
The rotation speed and the level at which the switch is
pulled during drilling is not stored to memory.
○
Fully carry out drilling in one go during auto stop mode.
○
The motor will stop even if you switch OFF within the
memory storage time.
○
When you switch OFF within the memory storage time,
the count will be reset. If you rework a task in which a
hole has been partially drilled, the memory storage time
will be fully recounted.
○
The auto stop function will remain active until canceled.
REACTIVE FORCE CONTROL
This product is equipped with a Reactive Force Control
(RFC) feature that reduces jerking of the tool body.
If the tool bit is suddenly overburdened, any jerking of the
tool body is reduced by activation of the slip clutch or by
stopping of the motor by the sensor built into the tool body.
If the motor is stopped because of overburdening detection
by the controller, the display lamp will blink while the switch
is pulled. In addition, the lamp will continue blinking for
approximately three seconds after the switch is released.
The motor will remain stopped while the lamp is blinking.
(
Fig. 16
)
Because the RFC feature may not activate or its performance
may be insu
ffi
cient depending on the working environment
and conditions, be careful not to suddenly overburden the
tool bit while operating.
●
Possible causes of sudden overburdening
Tool bit biting into material
Impact against nails, metal or other hard objects
Tasks involving prying or any excess application of
pressure, etc.
Also, other causes include any combination of the
aforementioned.
●
When the reactive force control (RFC) is triggered
When the RFC is triggered and the motor stops, turn
o
ff
the tool’s switch and remove the cause of the
overburdening before continuing operation.
Fig. 16
0000Book̲DH18DPB.indb 11
0000Book̲DH18DPB.indb 11
2020/09/29 11:02:58
2020/09/29 11:02:58
