14
English
○
Before starting work, check the nailing operation
switching device.
This HiKOKI nailer includes a nailing operation switching
device.
Before starting work, make sure that the switching
device is properly set.
If the switching device is not set properly, the nailer will
not operate correctly.
○
Never place your face, hands or feet near
fi
ring head
when using.
○
Do not drive nails on top of other nails or with Nailer at too
steep of an angle; nails can ricochet and hurt someone.
○
Do not drive nails into thin boards or near corners and
edges of workpiece. Nails can be driven through or away
from workpiece and hit someone.
○
Never drive nails from both sides of a wall at the same
time. Nails can be driven into and through the wall and
hit a person on the opposite side.
○
Never use Nailer which is defective or operating
abnormally.
○
Do not use Nailer as hammer.
○
Remove all remaining fasteners and battery from nailer
when:
1) doing maintenance and inspection;
2) checking proper operation of push lever and trigger;
3) attaching or removing the nose cap;
4) cleaning a jam;
5) it is not in use;
6) leaving work area;
7) moving it to another location; and
8) handing it to another person.
○
Remove battery from Nailer when:
1) loading nails;
2) turning the adjuster.
This HiKOKI nailer is equipped with a nailer operation
switching device.
Use FULL SEQUENTIAL ACTUATION MECHANISM or
CONTACT ACTUATION MECHANISM in accordance with
the work to be performed.
Explanation of the various nailing operations
○
FULL SEQUENTIAL ACTUATION MECHANISM:
First, press the push lever against the wood; next, pull
the trigger to drive the nail.
Follow the same sequence to continue driving nails.
After nailing once, nailing will not be possible again until
remove
fi
nger from the trigger and lift the tool o
ff
the
wood surface completely.
○
CONTACT ACTUATION MECHANISM:
CONTACT ACTUATION can follow two di
ff
erent
sequences, depending on your use.
To drive several nails:
1. Pull the trigger.
2. Press the push lever against the wood to drive the
nail.
3. If the trigger is held back, a nail will be driven each
time the push lever is pressed against the wood.
To drive a single nail:
1. Press the push lever against the wood.
2. Pull the trigger to drive the nail.
3. Remove your
fi
nger from the trigger and remove the
nailer from the wood.
[Dry-
fi
re lockout mechanism]
The NT1865DBAL, NT1865DBSL and NT1865DA
employ a preventive mechanism for unloaded operation.
The NT1865DBAL, NT1865DBSL and NT1865DA enter
a state where the push lever cannot be pushed up. This
takes place when the magazine is not loaded with nails
or when the remaining number of nails becomes less
than 6 or 9.
CAUTION
Use caution not to throw the push lever tip onto wood
when the push lever cannot be pushed up.
1. Nailing procedures
This Nailer is equipped with the push lever and does not
operate unless the push lever is depressed.
There are two methods of operation to drive nails with
this Nailer.
They
are:
1. Intermittent operation (Trigger
fi
re):
2. Continuous operation (Push lever
fi
re):
(1) Intermittent operation (Trigger
fi
re)
Use the FULL SEQUENTIAL ACTUATION MECHANISM
setting. (See
Fig. 17
)
WARNING
○
For intermittent operation, Set the nailing operation switch
to FULL SEQUENTIAL ACTUATION MECHANISM
(Nailing operation indicator is light in blue.) (i.e. Set to
SINGLE ACTUATION MECHANISM.)
○
To avoid double
fi
ring or accidental
fi
ring due to recoil.
1)
Set to FULL SEQUENTIAL ACTUATION
MECHANISM.
2) Pull the trigger rapidly and
fi
rmly.
Set the nailing operation switch to FULL SEQUENTIAL
ACTUATION MECHANISM (Nailing operation indicator
is light in blue.)
(to set to FULL SEQUENTIAL ACTUATION
MECHANISM).
(Set the switching device to the nailing operation
indicator light in blue mode completely as shown in
the
Fig. 17
. Otherwise, it will be set to CONTACT
ACTUATION MECHANISM.)
Position the nail outlet on the workpiece with
fi
nger o
ff
the trigger.
Depress the push lever
fi
rmly until it is completely
depressed.
Pull the trigger to drive a nail.
Remove
fi
nger from the trigger and lift the tool o
ff
the
wood surface completely.
To continue nailing in a separate location, move the nailer
along the wood, repeating steps - as required.
NOTE
Operations and should be done within 2 seconds
of each other. If more than 2 seconds pass after , the
Nailer will not work properly. If this happens, retry from
.
(2) Continuous operation (Push lever
fi
re)
Using CONTACT ACTUATION MECHANISM (See
Fig.
18
)
WARNING
To avoid double
fi
ring or accidental
fi
ring due to recoil.
1) Do not press the nailer against the wood with
excessive force.
2) Separate the nailer from the wood as it recoils after
nailing.
Set the nailing operation switch to CONTACT
ACTUATION MECHANISM (Nailing operation indicator
is blink in blue.)
(to set to CONTACT ACTUATION MECHANISM).
(Set the switching device to the nailing operation
indicator blink in blue completely as shown in the
Fig. 18
. Otherwise, it will not operate properly.)
Pull the trigger with the Nailer o
ff
the workpiece.
Depress the push lever against the workpiece to drive a
nail.
Move the Nailer along the workpiece with a bouncing
motion.
Each depression of the push lever will drive a nail.
As soon as the desired number of nails have been driven,
remove
fi
nger from the trigger.
NOTE
Operations and should be done within 2 seconds
of each other. If more than 2 seconds pass after , the
Nailer will not work properly. If this happens, retry from
.
0000Book̲NT1865DBAL.indb 14
0000Book̲NT1865DBAL.indb 14
2020/12/09 9:37:08
2020/12/09 9:37:08
