15
English
WARNING
○
Keep your
fi
nger o
ff
the trigger except during nailing
operation, because serious injury could result if the push
lever accidentally contacts you or others in work area.
○
Keep hands and body away from the discharge area.
This HiKOKI nailer may bounce from the recoil of driving
a nail and unwanted subsequent nail may be driven,
possibly causing injury.
NOTE
○
If all warnings and instructions are followed, safe
operation is possible with all two systems: FULL
SEQUENTIAL ACTUATION MECHANISM, CONTACT
ACTUATION MECHANISM.
○
Always handle nails and package carefully. If nails are
dropped, collating bond may be broken, which will cause
mis-feeding and jamming.
○
After nailing:
1) remove battery from the Nailer;
2) remove all nails from the Nailer;
2. Adjusting the nailing depth
To assure that each nail penetrates to the same depth,
be sure that the Nailer is always held
fi
rmly against the
workpiece.
If nails are driven too deep or shallow into the workpiece,
adjust the nailing in the following order.
Remove the battery from the Nailer.
If nails are driven too deep, turn the adjuster to the
shallow side. (See
Fig. 19
)
Adjustments are in half-turn increments.
If nails are driven too shallow, turn the adjuster to the
deep side. (See
Fig. 20
)
Stop turning the adjuster when a suitable position is
reached for a nailing test.
Connect the battery to the Nailer.
ALWAYS WEAR SAFETY GLASSES.
Perform a nailing test.
Remove the battery from the Nailer.
Choose a suitable position for adjuster.
3. Using the hook (See Fig. 21, 22, 23)
WARNING
When using the hook, turn o
ff
the power switch (green
light “OFF”). Pay su
ffi
cient attention so that the main
equipment does not fall.
If the tool falls, there is a risk of accident.
Hook can be installed on the left or right side. (excluding
NT1865DBAL and NT1865DA)
Remove the battery, then remove all remaining nails
from the magazine.
Securely hold the main unit and remove the screw using
a screwdriver. (See
Fig. 21
)
Remove the hook and hook plate. (See
Fig. 22
)
Install the hook on the other side and securely fasten
with screw. (See
Fig. 23
)
NOTE
Hook can be used as a hanger.
4. Using the nose cap (See Fig. 24, 25)
WARNING
When attaching or detaching the nose cap, be sure
to remove your
fi
nger from the trigger and remove all
remaining fasteners and the battery from the nailer.
If you like to protect the surface of workpiece against
scratches or markings made by the push lever, attach the
accessory nose cap to the push lever.
Remove all remaining fasteners and battery from nailer.
Put the nose cap to the toe of the push lever.
The nose cap is marked to indicate the exit point of the
nail, making alignment easier.
When not using the nose cap, secure in the storage
compartment located on the reverse side of the
magazine.
NOTE
The nose cap may reduce nailing depth due to its
thickness. Re-adjustment of nailing depth is required.
5. Clearing a jam
If nails are jammed in
fi
ring head, remove it, and adjust
the nailing in the following order.
CAUTION
Remove the battery from the Nailer.
Remove the battery from the Nailer.
Remove all nails.
Release the Lock lever and open guide plate. (See
Fig. 26
)
Remove the jammed nail with a slotted-head screwdriver.
(See
Fig. 27
)
CAUTION
○
NEVER hit the driver blade.
○
NEVER point the tool at yourself or another person, to
avoid risk of injury by mis-
fi
ring.
Even if the battery is removed from the nailer, there is still
energy of compressed air remaining inside.
Close guide plate and latch.
NOTE
In case of frequent jam, contact a HiKOKI authorized
service center.
MAINTENANCE AND INSPECTION
CAUTION
Be sure to remove all remaining fasteners and battery
from the nailer before maintenance and inspection.
1. Inspecting the magazine
Remove battery from the Nailer.
Clean the magazine. Remove dust and wooden
chips which may have accumulated in the magazine.
CAUTION
Check that the nail feeder slides smoothly by pulling it
with
fi
nger.
If not smooth, nails can be driven at an irregular angle
and hurt someone.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspection of terminals (tool and battery)
Check to make sure that swarf and dust have not
collected on the terminals.
On occasion check prior, during and after operation.
CAUTION
Remove any swarf or dust which may have collected on
the terminals.
Failure to do so may result in malfunction.
5. Cleaning on the outside
When the power tool is stained, wipe with a soft dry cloth
or a cloth moistened with soapy water. Do not use chloric
solvents, gasoline or paint thinner, for they melt plastics.
6. Storage
Store the power tool in a place in which the temperature
is less than 40°C and out of reach of children.
NOTE
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully
charged before storing them.
Prolonged storage (3 months or more) of batteries with
a low charge may result in performance deterioration,
signi
fi
cantly reducing battery usage time or rendering
the batteries incapable of holding a charge.
However,
signi
fi
cantly reduced battery usage time may
be recovered by repeatedly charging and using the
batteries two to
fi
ve times.
If the battery usage time is extremely short despite
repeated charging and use, consider the batteries dead
and purchase new batteries.
0000Book̲NT1865DBAL.indb 15
0000Book̲NT1865DBAL.indb 15
2020/12/09 9:37:09
2020/12/09 9:37:09
