background image

G4 Mobile Recorder• Installation Guide and Platform Settings

 

 

©  2020 Hangzhou Hikauto Technology Co., Ltd. All rights reserved. 
 
This  Manual  is  the  property  of  Hangzhou  Hikauto  Technology  Co.,  Ltd.  or  its  affiliates  (hereinafter  referred  to  as 
"Hikauto"), and it cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without 
the  prior  written  permission  of  Hikvision.  Unless  otherwise  expressly  stated  herein,  Hikauto  does  not  make  any 
warranties,  guarantees  or  representations,  express  or  implied,  regarding  to  the  Manual,  any  information  contained 
herein. 
 
About this Manual 
The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information 
hereinafter  are for  description  and explanation  only.  The  information contained  in  the Manual is  subject  to  change, 
without notice, due to firmware updates or other reasons.   
Please use this Manual with the guidance and assistance of professionals trained in supporting the Product.   
 
Trademarks Acknowledgement 

 

  and other Hikauto’s trademarks and logos are the properties of Hikauto in various jurisdictions.   

 

Other trademarks and logos mentioned are the properties of their respective owners.   
 

LEGAL DISCLAIMER 
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITS 
HARDWARE,  SOFTWARE  AND  FIRMWARE,  ARE  PROVIDED  “AS  IS”  AND  “WITH  ALL  FAULTS  AND  ERRORS”.  HIKAUTO 
MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY 
QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN  RISK. IN NO 
EVENT  WILL  HIKAUTO BE LIABLE  TO  YOU  FOR  ANY  SPECIAL,  CONSEQUENTIAL,  INCIDENTAL,  OR INDIRECT DAMAGES, 
INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA, 
CORRUPTION  OF  SYSTEMS,  OR  LOSS  OF  DOCUMENTATION,  WHETHER  BASED  ON  BREACH  OF  CONTRACT,  TORT 
(INCLUDING  NEGLIGENCE),  PRODUCT  LIABILITY,  OR OTHERWISE,  IN  CONNECTION  WITH  THE  USE  OF  THE  PRODUCT, 
EVEN IF HIKAUTO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS.   
YOU ACKNOWLEDGE THAT THE NATURE OF INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKAUTO SHALL 
NOT  TAKE  ANY  RESPONSIBILITIES  FOR  ABNORMAL  OPERATION, PRIVACY  LEAKAGE  OR OTHER  DAMAGES RESULTING 
FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKAUTO 
WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.   
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE 
FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING 
THIS  PRODUCT IN  A  MANNER  THAT DOES  NOT  INFRINGE ON  THE  RIGHTS OF  THIRD PARTIES,  INCLUDING  WITHOUT 
LIMITATION,  RIGHTS  OF  PUBLICITY,  INTELLECTUAL  PROPERTY  RIGHTS,  OR  DATA  PROTECTION  AND  OTHER  PRIVACY 
RIGHTS.  YOU  SHALL  NOT  USE  THIS  PRODUCT  FOR  ANY  PROHIBITED  END-USES,  INCLUDING  THE  DEVELOPMENT  OR 
PRODUCTION  OF  WEAPONS  OF  MASS  DESTRUCTION,  THE  DEVELOPMENT  OR  PRODUCTION  OF  CHEMICAL  OR 
BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR 
FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES. 
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. 

 

 

 

Summary of Contents for AE-DI5042-G4
















































Reviews: