background image

  Warnings 

 

The device should be used in compliance with 

local laws and electrical safety regulations. Refer to 
the appropriate documentation for detailed 
information. 

 

The device should be used in the environment 

within temperature range from -10 °C to 50 °C (14 °F 
to 122 °F), humidity ≤90%, and height ≤5000 m. 

 

The input voltage should conform to IEC61010-1 

standard: SELV (Safety Extra Low Voltage) and the 
Limited Power Source ((5 V DC/0.3 A). 

 

Make sure the plug is properly connected to the 

power socket. 

 

If smoke, odor, or noise arises from the device, 

immediately turn off the power, unplug the power 
cable, and contact the service center. 

 

The installer and user are responsible for 

password and security configuration and its settings. 

 

  Cautions 

 

Do not drop the device or subject it to physical 

shock. 

 

Wipe the device gently with a clean cloth and a 

small quantity of ethanol, if necessary. 

 

Do not aim the lens at the sun or any other bright 

light.   

 

When any laser equipment is in use, make sure 

that the device lens is not exposed to the laser beam, 
or it may burn out. 

 

Do not expose the device to high electromagnetic 

radiation or extremely hot, cold, dusty, or damp 
environments.   

 

Place the device in a dry and well-ventilated 

environment. 

 

Keep non-waterproof devices away from liquids. 

 

Keep the device in original or similar packaging 

while transporting it. 

 

A few device components (e.g., electrolytic 

capacitor) require regular replacement. The average 
lifespan varies, so periodic checking is recommended. 
Contact your dealer for details. 

 

Never attempt to disassemble the device. 

 

Improper use or replacement of the battery may 

result in explosion hazard. Replace with the same or 
equivalent type only. Dispose of used batteries in 
conformance with the instructions provided by the 
battery manufacturer.   

 

The built-in battery can not be dismantled. Please 

contact manufacture for repair if necessary. The 
battery type is E097-27-1P1S18650, and the rated 
voltage and capacity is 3.6 VDC/3.35 Ah (12.06 Wh). 
The battery may explode if it is replaced by an 
incorrect type. Dispose of used batteries according 
to the instructions. 

 

For long-term storage of the battery, make sure 

you fully charge it every half year, to ensure the 
battery quality. Otherwise, you may damage the 
battery. 

Warnings Follow 
these safeguards to 
prevent serious injury 
or death. 

Cautions Follow these 
precautions to 
prevent potential 
injury or material 
damage. 

Summary of Contents for DS-2TP31-3AUF













Reviews: