background image

Keypad User Manual 

 

Regulatory Information 

FCC Information 

Please take attention that changes or modification not expressly approved by the party responsible for 

compliance could void the user’s authority to operate the equipment. 

FCC compliance:

 This equipment has been tested and found to comply with the limits for a Class B 

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable 

protection against harmful interference in a residential installation. This equipment generates, uses 

and can radiate radio frequency energy and, if not installed and used in accordance with the 

instructions, may cause harmful interference to radio communications. However, there is no guarantee 

that interference will not occur in a particular installation. If this equipment does cause harmful 

interference to radio or television reception, which can be determined by turning the equipment off 

and on, the user is encouraged to try to correct the interference by one or more of the following 

measures: 

Reorient or relocate the receiving antenna. 

Increase the separation between the equipment and receiver. 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected. 

Consult the dealer or an experienced radio/TV technician for help. 

This equipment should be installed and operated with a minimum distance 20cm between the radiator 

and your body. 

FCC Conditions 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 

conditions: 

1. This device may not cause harmful interference. 

2. This device must accept any interference received, including interference that may cause undesired 

operation 

EU Conformity Statement 

 

This product and - if applicable - the supplied accessories too are marked with "CE" 

and comply therefore with the applicable harmonized European standards listed 

under the EMC Directive 2014/30/EU, the RE Directive 2014/53/EU, the RoHS 

Directive 2011/65/EU.

 

 

 

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed 

of as unsorted municipal waste in the European Union. For proper recycling, return 

this product to your local supplier upon the purchase of equivalent new equipment, 

Summary of Contents for DS-PK00-LCD series


















Reviews: