background image

Keypad User Manual 

 

Safety Instruction 

These instructions are intended to ensure that the user can use the product correctly to avoid danger 

or property loss. 

The precaution measure is divided into ‘Warnings’ and ‘Cautions’: 

Warnings

: Serious injury or death may be caused if any of these warnings are neglected. 

Cautions

: Injury or equipment damage may be caused if any of these cautions are neglected. 

 

 

Warnings

  Follow  these  safeguards  to  prevent 

serious injury or death. 

Cautions

  Follow  these  precautions  to  prevent 

potential injury or material damage. 

Warnings: 

 

Please  adopt  the  power  adapter  which  can  meet  the  safety  extra  low  voltage  (SELV)  standard. 

The power consumption cannot be less than the required value. 

 

Do  not  connect  several  devices  to  one  power  adapter  as  an  adapter  overload  may  cause 

over-heating and can be a fire hazard. 

 

When the product is installed on a wall or ceiling, the device should be firmly fixed. 

 

To reduce the risk  of  fire or  electrical  shock, do not  expose the  indoor used product to rain or 

moisture. 

 

This installation should be made by a qualified service person and should conform to all the local 

codes. 

 

Please  install  blackouts  equipment  into  the  power  supply  circuit  for  convenient  supply 

interruption. 

 

If the product does not work properly, please contact your dealer or the nearest service center. 

Never attempt to disassemble the product yourself. (We shall not assume any responsibility for 

problems caused by unauthorized repair or maintenance.) 

 

Please  do  not  look  directly  into  the  laser  light  within  6  meters  because  laser  is  hazardous  to 

humans. 

Summary of Contents for DS-PK00-LCD series


















Reviews: