background image

Vision Box User Manual 

Regulatory Information 

FCC Information 

Please  take  attention  that  changes  or  modification  not  expressly  approved  by  the  party 

responsible for compliance could void the user’s authority to operate the equipment. 
FCC compliance: This equipment has been tested and found to comply with the limits for a Class A 
digital  device,  pursuant  to  part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide 
reasonable  protection  against  harmful  interference  when  the  equipment  is  operated  in  a 
commercial environment. This equipment generates, uses, and can radiate radio frequency energy 

and,  if  not  installed  and  used  in  accordance  with  the  instruction  manual,  may  cause  harmful 
interference to radio communications. Operation of this equipment in a residential area is likely to 
cause harmful interference in which case the user will be required to correct the interference at 
his own expense. 

FCC Conditions 

This  device  complies  with  part  15  of  the  FCC  Rules.  Operation  is  subject  to  the  following  two 
conditions: 

1. This device may not cause harmful interference. 

2.  This  device  must  accept  any  interference  received,  including  interference  that  may  cause 
undesired operation. 

EU Conformity Statement 

This product and - if applicable - the supplied accessories too are marked with "CE" and 

comply  therefore  with  the  applicable  harmonized  European  standards  listed  under  the 

EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU.   

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of 

as  unsorted  municipal  waste  in  the  European  Union.  For  proper  recycling,  return  this 
product  to  your  local  supplier  upon  the  purchase  of  equivalent  new  equipment,  or 

dispose of it at designated collection points. For more information see: 

www.recyclethis.info

 

2006/66/EC (battery directive): This product contains a battery that cannot be disposed 

of as unsorted municipal waste in the European Union. See the product documentation 

for  specific  battery  information.  The  battery  is  marked  with  this  symbol,  which  may 

include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return 
the  battery  to  your  supplier  or  to  a  designated  collection  point.  For  more  information  see: 

www.recyclethis.info 

Industry Canada ICES-003 Compliance 

This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.   

Summary of Contents for MV-VB2100-032G























Reviews: