background image

SAFETY INFORMATION

4

DANGER

• CARBON MONOXIDE HAZARD
• This heater is a combustion appliance. All 
combustion appliances produce carbon monoxide 
(CO) during the combustion process. This product is 
designed to produce extremely minute, non-hazardous
amounts of CO if used and maintained in accordance 
with all warnings and instructions. Do not block air 
flow into or out of the heater.
• Carbon Monoxide (CO) poisoning produces flu-like
symptoms, watery eyes, headaches, dizziness, fatigue
and possibly death. You can't see it and you can't 
smell it. It's an invisible killer. If these symptoms are 
present during operation of this product get fresh air 
immediately!
• For outdoor use only.
• Never use inside house, or other unventilated or
enclosed areas.
• This heater consumes air (oxygen). Do not use in
unventilated or enclosed areas to avoid endangering
your life.

WARNING

DANGER

• EXPLOSION - FIRE HAZARD
• Keep solid combustibles, such as building materials,
paper or cardboard, a safe distance away from the 
heater as recommended by the instructions.
• Provide adequate clearances around air openings
into the combustion chamber.
• Never use the heater in spaces which do or may 
contain volatile or airborne combustibles, or products
such as gasoline, solvents, paint thinner, dust particles
or unknown chemicals.
• During operation, this product can be a source of
ignition. Keep heater area clear and free from 
combustible materials, gasoline, paint thinner, cleaning
solvents and other flammable vapors and liquids. Do 
not use heater in areas with high dust content. 
Minimum heater clearances from combustible 
materials: three (3) feet from the sides & two (2) feet
from the top.

We cannot foresee every use which may be made of 
our heaters.
Check with your local fire safety authority if you have
questions about heater use.
Other standards govern the use of fuel gases and heat
producing products for specific uses. Your local 
authorities can advise you about these.
If no local codes exist, follow National Fuel Gas Code,
ANSI Z223.1. In Canada, installation must conform to
local codes. If no local codes exist, follow the current 
National standards of CANADA CAN/CGA-B 149.2.

DANGER

WARNING

Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
An LP-cylinder not connected for use shall not be 
stored in the vicinity of this or any other appliance.

WARNING

Improper installation, adjustment, alteration, service or 
maintenance can cause property damage, injury or 
death. Read the installation, operation and 
maintenance instructions thoroughly before installing
or servicing this equipment.

CARBON MONOXIDE HAZARD
This appliance can produce 
carbon monoxide which has 
no odor. Using it in an enclosed
space can kill you. Never use this
appliance in an enclosed space
such as a camper, tent or home.

WARNING:

For Outdoor Use Only

DANGER

• EXPLOSION - FIRE HAZARD
• Never store propane near high heat, open flames, 
pilot lights, direct sunlight, other ignition sources or 
where temperatures exceed 120 degrees F (49°C).
• Propane vapors are heavier than air and can 
accumulate in low places. If you smell gas, leave the
area immediately.
• Never install or remove propane cylinder while heater
is lighted, near flame, pilot lights, other ignition sources
or while heater is hot to touch.
• This heater is red hot during use and can ignite
flammables too close to the burner. Keep flammables
at least 3 feet from sides & 2 feet from top. Keep 
gasoline and other flammable liquids and vapors well 
away from heater.
• Store the propane cylinder outdoors in a well ventilated
space out of reach of children. Never store the propane 
cylinder in an enclosed area (house, garage, etc.). If 
heater is to be stored indoors, disconnect the propane 
cylinder for outdoor storage.

WARNING

WARNING indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.

Summary of Contents for HLDS032
















Reviews: