TROUBLESHOOTING
This chapter lists the most common problems linked with the use of the machine. If you are unable to resolve the problems with the information given here, please contact your nearest assistance centre.
PROBLEM
POSSIBLE CAUSE
SOLUTION
THE MACHINE DOES NOT
START
The main switch is set to “0”.
Make sure that the main switch is at "I", if not turn the key to the left.
Check that when switched on there are no alarm messages on the command
display.
Stop the machine immediately, and contact a specialised service centre.
Make sure that the batteries are correctly connected to each other and that the
battery connector is connected to the electrical system connector.
Contact a Fimap assistance centre or qualified technician.
Check the charge level of the batteries.
If the battery charge level is critical, perform a complete recharge cycle (see
paragraph
”).
THE BATTERIES ARE NOT
CHARGED CORRECTLY
(VERSIONS WITHOUT AN ON
BOARD BATTERY CHARGER)
The connector of the battery charger cable is not properly inserted in the battery
connector.
Connect the battery charger cable connector to the battery connector again.
The plug on the battery charger's power cable is not correctly inserted into the
electrical outlet.
Check that the battery charger power supply cable plug is connected to the mains
socket.
The characteristics of the mains power supply do not correspond to those required
by the battery charger.
Check that the characteristics in the battery charger plate are the same as those of
the mains supply.
The LEDs of the battery charger blink repeatedly.
Referring to the battery charger use and maintenance manual, check the meaning
of the flashing signals that the battery charger emits dung the battery recharge
stage.
THE BATTERIES ARE NOT
CHARGED CORRECTLY
(VERSIONS WITH AN ON
BOARD BATTERY CHARGER)
The plug on the battery charger's cable is not correctly inserted into the socket on
the battery charger itself.
Reconnect the battery charger's power cable.
The plug on the battery charger's power cable is not correctly inserted into the
electrical outlet.
Check that the battery charger power supply cable plug is connected to the mains
socket.
The characteristics of the mains power supply do not correspond to those required
by the battery charger.
Check that the characteristics in the battery charger plate are the same as those of
the mains supply.
The LEDs of the battery charger blink repeatedly.
Referring to the battery charger use and maintenance manual, check the meaning
of the flashing signals that the battery charger emits dung the battery recharge
stage.
THE MACHINE HAS A VERY
LOW WORK AUTONOMY
Check the battery charge level, check the symbol on the command display.
If the battery charge level is critical, perform a complete recharge cycle (see
paragraph
”).
INSUFFICIENT DETERGENT
SOLUTION ON THE
BRUSHES
The quantity of detergent solution in the water system is not sufficient for the work
to be carried out.
Check that the amount of detergent solution present in the machine's water system
is sufficient for the work to be carried out.
Detergent solution filter obstructed.
Check the detergent solution filter isn't obstructed. If it is, clean it (see “
THE MACHINE DOES NOT
CLEAN CORRECTLY
Not enough detergent solution comes out.
Read the section “
INSUFFICIENT DETERGENT SOLUTION ON THE BRUSHES
”.
The brushes have not been inserted correctly in the machine.
Check that the disc brushes have been correctly inserted in the machine (see
The brush bristles are excessively worn.
Check the state of wear of the brush and, if necessary, replace it.
THE SQUEEGEE DOES NOT
DRY PERFECTLY
The vacuum unit is obstructed.
Make sure the squeegee is free of obstructions (read “
Make sure the vacuum tube is free of obstructions (see “
Check that the filters in the recovery tank are not clogged (see paragraph
CLEANING THE RECOVERY TANK FILTERS
The cap on the recovery tank drainage tube is not properly positioned.
Check that the cap on the recovery tank drainage tube is positioned properly.
The recovery tank lid is not positioned correctly.
Check that the recovery tank lid is properly positioned on the machine.
EXCESSIVE FOAM
PRODUCTION
The detergent being used is not suitable.
Check that a low foam detergent has been used. If necessary, add a small quantity
of anti-foam liquid to the recovery tank.
The floor is not very dirty.
Dilute the detergent more.
THE MACHINE DOES NOT
VACUUM CORRECTLY
The recovery tank is full.
Empty the recovery tank (read “
The vacuum device is obstructed
Read the section “
THE SQUEEGEE DOES NOT DRY PERFECTLY
28
Summary of Contents for TRIDENT R26SC PRO
Page 2: ......
Page 3: ...ENGLISH 4 ESPA OLA 30 FRAN AIS 56 3 ESPA OLA FRAN AIS ENGLISH...
Page 82: ...ESPA OLA FRAN AIS ENGLISH 82...
Page 83: ......
