NB
: with this working program both the brush head and the squeegee support are put in the
rest position (raised off the floor) and the motors switch off with the respective switching off
delays (even if the drive pedal is not pressed). When the drive pedal is pressed only the
traction motor is powered.
NB
: in the DS selector the transport program symbol (A) is green.
NB
: the grey symbols show working programs that are not active. the green symbols show
working programs that are active.
The icons that could be visible are:
1. FFM symbol, if visible it shows that the system is operating.
2. FSS symbol, if visible it shows that the system is operating.
3. Side brush/es, if visible it shows that the side brush/es is/are enabled.
4. Working lights symbol, if visible it shows that the working lights are on.
5. General alarm symbol.
ATTENTION
: if visible stop the machine, to continue working (read the paragraph “
”).
6.
Recovery tank full float symbol,
ATTENTION
: if visible it shows that the solution level in the tank has a reached a level beyond
which the vacuum motor might be compromised, therefore the tank needs to be emptied before
continuing the work (read the section “
7.
Solution tank empty float symbol.
ATTENTION
: if visible it shows that the detergent solution in the tank has a reached a level
beyond which the solenoid valve might not deliver solution onto the brushes, therefore the tank
needs to be filled up before continuing the work (read the section “
”).
8. Eco-Mode button.
NB
: if the Eco-Mode button (8) is pressed in the transfer mode the scrubbing with drying
program is started in economic mode.
9. Menu button.
10. Rear camera button.
NB
: pressing the rear camera button (10) if present the video camera on the back of the machine
will start, read the section “
11. Zone button.
NB
: if the Zone button (11) is pressed in transfer mode, the window for selecting the zone opens
(read the section “
”
); after selecting a zone, the machine shifts into
scrubbing with drying mode with the program of the zone selected.
12. Text indicator.
NB
: in the text indicator (12) it is possible to see that the zone program has been selected or
whether you are in transport mode if there is the word “DRIVE”.
NB
: If you need to activate the dipped headlights during the transfer, read the section “
SCRUBBING WITHOUT DRYING
OFFICE
0000.00
100%
9
8
10
11
12
1
5
2
6
3
7
4
By selecting the "SCRUBBING WITHOUT DRYING” program, the command display screen will appear
as in the adjacent figure.
NB
: with this working program pressure on the drive pedal only brings the brush heads to the
work position (in contact with the floor), while the squeegee remains in the rest position (raised
from the floor). The brush head solenoid valve and the water system pump are powered up
(only if the detergent solution is other than zero). When the drive pedal is pressed the brush
heads, the solenoid valve, the electric pump and the traction motor are powered up.
N.B.
: in the DS selector the symbol of the scrubbing without drying program (B) is green.
N.B.
: the grey symbols show working programs that are not active. the green symbols show
working programs that are active.
N.B.
: when the drive pedal is released all the brush head motors stop with the respective delays.
After the “Reset Delay”time all the brush heads are taken to the rest position (raised off the floor).
by pressing the forward movement pedal it will start working with the same program and with the
same parameters that were set before it stopped.
N.B. :
if you reverse with this program active the brush head will remain in contact with the floor,
the motor will continue working but the solenoid valve will not deliver the detergent solution to
the brushes.
The icons that could be visible are:
1. FFM symbol, if visible it shows that the system is operating.
2. FSS symbol, if visible it shows that the system is operating.
3. Side brush/es, if visible it shows that the side brush/es is/are enabled.
4. Working lights symbol, if visible it shows that the working lights are on.
5. General alarm symbol.
ATTENTION
: if visible stop the machine, to continue working (read the paragraph “
6.
Recovery tank full float symbol.
ATTENTION:
if visible it shows that the solution level in the tank has a reached a level beyond
which the vacuum motor might be compromised, therefore the tank needs to be emptied before
continuing the work (read the section “
7.
Solution tank empty float symbol.
ATTENTION
: if visible it shows that the detergent solution in the tank has a reached a level
beyond which the solenoid valve might not deliver solution onto the brushes, therefore the tank
needs to be filled up before continuing the work (read the section “
8. Eco-Mode button.
N.B.
: if you press the Eco-Mode button (8) you start the working program currently in use in
economic mode, to remove the economic mode read the section “
”.
9. Menu button.
10. Rear camera button.
N.B.
: pressing the rear camera button (10) if present the video camera on the back of the
machine will start, read the section “
” to continue working.
11. Zone button
N.B.
: if you need to change the program used when working, press the Zone button (11) (read
”).
12. Text indicator.
N.B.
: in the text indicator (12) it is possible to see that the zone program has been selected or
whether you are in transport mode if there is the word “DRIVE”.
N.B.
: If you need to activate the dipped headlights when working, read the section “
”.
N.B.
: If the side brush need to be used when working read the paragraph “
ACTIVATING THE
SIDE BRUSH
”.
ATTENTION: never switch off the machine while the squeegee and/
or brush head is in contact with the floor
DRYING
OFFICE
0000.00
100%
1
5
2
6
3
7
4
9
11
8
10
By selecting the "DRYING” program, the command display screen will appear as in the adjacent figure.
NB
: with this working program pressure on the drive pedal only brings the squeegee to the
work position (in contact with the floor), while the brush head remains in the rest position
(raised from the floor). When the drive pedal is pressed both the vacuum motor and the
traction motor are powered.
NB
: in the DS selector the drying program symbol (C) is green.
NB
: the grey symbols show working programs that are not active. the green symbols show
working programs that are active.
NB
: when the drive pedal is released the vacuum motor will stop with the respective delay. After
the “Reset Delay” time all the squeegee support is taken to the rest position (raised off the floor).
by pressing the forward movement pedal it will start working with the same program and with the
same parameters that were set before it stopped.
21
