5. Remove the squeegee unit from the slits in the squeegee connector (
Fig.4
).
6. Release the tank cleaning accessory (4) (at the back of the machine) from the retainers (
Fig.5
).
7. Activate the optional tank cleaning kit ON/OFF pump by pressing the button (5) on the back of
the steering column (
Fig.6
).
CAUTION
: when using the optional tank cleaning kit, you are advised to always wear goggles
to avoid any risk of serious injury to your eyes.
N.B.
: Before starting the optional tank cleaning kit, check the level indicator (6) to see how
much solution there is in the recovery tank (
Fig.7
).
8. Activate the solution jet by pressing the lever in the tank cleaning accessory. Make sure the jet is
pointing into the tank before pressing the lever.
N.B.
: to adjust the solution jet from the
tank cleaning accessory, turn the knob (7) on the
accessory itself
(
Fig.8
).
N.B.
: to adjust the intensity of the solution jet from the
tank cleaning accessory, turn the knob
(8) on the accessory itself
(
Fig.9
).
N.B.
: to stop the solution jet,
use the lever (9) on the tank cleaning accessory (
Fig.10
).
9.
Thoroughly clean the vacuum chamber of the squeegee body, first with a jet of water and then
with a damp cloth.
N.B.
: the place designated for this operation must comply with current environmental protection
regulations.
10.
Thoroughly clean the rear rubber blade of the squeegee body, first with a jet of water and then
with a damp cloth.
11.
Thoroughly clean the front rubber blade of the squeegee body, first with a jet of water and then
with a damp cloth.
12. Thoroughly clean the vacuum nozzle with a jet of water, and then with a damp cloth.
13. Proceed in the opposite order to reassemble all the parts.
5
4
6
5
4
7
8
6
7
9
8
10
9
CLEANING THE BRUSH HEAD BRUSHES (SCRUBBING VERSION)
Careful cleaning of the brush guarantees better cleaning of the floor as well as a longer brush head gear
motor lifespan. To clean the brush, proceed as follows:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “
”).
CAUTION
: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
3. Open the machine's left lateral carter (1) (
Fig.1
).
4.
Remove the left splashguard casing (2), remembering beforehand to move the fixing anchors (3) on
the brush head body into the maintenance position (
Fig.2
).
5. Press the brush locking pin (4) (
Fig.3
).
6. Keeping the pin (4) pressed, turn the brush clockwise until it is locked (
Fig.4
).
3
1
2
1
2
3
4
4
7. Turn until the button is pushed towards the outside of the coupling spring and is locked into place.
8. Clean the brush under a stream of running water to remove any impurities from its bristles. Check
the wear status of the bristles and replace the brushes if they are excessively consumed (the
bristles' protrusion must not be less than 10 mm; this distance is indicated on the brush by the
yellow band). Read the paragraph “
ASSEMBLING THE BRUSH HEAD BRUSHES (SCRUBBING
9. After checking to make sure that the brush is clean, reassemble it and move on to the one on the
right hand side.
N.B.
: you are advised to invert the right and left-hand brushes every day.
N.B.
: The image in
Fig.4
indicates the direction of rotation for uncoupling the left brush; the right
brush must be turned in the opposite direction.
ATTENTION
: If the brushes are not new however, and have deformed bristles, it is better to
reassemble them in the same position (the right-hand one on the right, and the left-hand one
on the left), to prevent the different inclination of the bristles producing an overload on the
brush motor as well as excessive vibrations.
To clean the brush with the spray gun kit, proceed as follows:
1. Take the machine to the maintenance area.
2. Using the DS selector on the control display (
Fig.1
), select the “transfer” program” (1).
3. Go to the front of the machine.
ATTENTION:
these operations must be carried out using protective gloves to avoid any
possible contact with the edges or tips of metal objects.
4. Open the machine's left lateral carter (2) (
Fig.2
).
5.
Remove the left-hand splashguard (3) and move the fixing anchors (4) on the brush head body into
the maintenance position (
Fig.3
).
6. Press the brush locking pin (5) (
Fig.4
).
7. Keeping the pin (5) pressed, turn the brush clockwise until it is locked (
Fig.5
).
CAUTION
: users are advised to always wear protective gloves, to avoid the risk of serious
injury to hands.
8. Release the tank cleaning accessory (6) (at the back of the machine) from the retainers (
Fig.6
).
9. Activate the optional tank cleaning kit ON/OFF pump by pressing the button (7) on the back of
the machine (
Fig.7
).
CAUTION
: when using the optional tank cleaning kit, you are advised to always wear goggles
to avoid any risk of serious injury to your eyes.
N.B.
: Before starting the optional tank cleaning kit, check the level indicator (8) to see how
much solution there is in the solution tank (
Fig.8
).
10. Activate the solution jet by pressing the lever in the tank cleaning accessory.
N.B.
: to adjust the solution jet from the
tank cleaning accessory, turn the knob (9) on the
accessory itself
(
Fig.9
).
N.B.
: to adjust the intensity of the solution jet from the
tank cleaning accessory, turn the knob
(10) on the accessory itself
(
Fig.10
).
N.B.
: to stop the solution jet,
use the lever (11) on the tank cleaning accessory (
Fig.11
).
DRIVE
0000.00
100%
1
2
3
2
3
4
1
5
4
5
6
6
9
7
9
7
8
8
10
10
11
11
28
