To clean the debris hopper with the spray gun kit, proceed as follows:
1. Take the machine to the maintenance area.
2. Using the DS selector on the control display (
Fig.1
), select the “transfer” program” (1).
3. Go to the front right of the machine.
ATTENTION
: these operations must be carried out using protective gloves to avoid any
possible contact with the edges or tips of metal objects.
4. Open the machine's left lateral carter (2) (
Fig.2
).
5. Release the debris hopper locking pin (3) (
Fig.3
).
6. Use the handle (4) to extract the debris hopper (
Fig.4
) and empty it.
7. Release the tank cleaning accessory (5) (at the back of the machine) from the retainers (
Fig.5
).
8. Activate the optional tank cleaning kit ON/OFF pump by pressing the button (6) on the back of
the machine (
Fig.6
).
CAUTION
: when using the optional tank cleaning kit, you are advised to always wear goggles
to avoid any risk of serious injury to your eyes.
N.B.
: Before starting the optional tank cleaning kit, check the level indicator (7) to see how
much solution there is in the solution tank (
Fig.7
).
9. Activate the solution jet by pressing the lever in the tank cleaning accessory.
N.B.
: to adjust the solution jet from the
tank cleaning accessory, turn the knob (8) on the
accessory itself
(
Fig.8
).
N.B.
: to adjust the intensity of the solution jet from the
tank cleaning accessory, turn the knob
(9) on the accessory itself
(
Fig.9
).
N.B.
: to stop the solution jet,
use the lever (10) on the tank cleaning accessory (
Fig.10
).
10. Clean the inside with a jet of water, and use a brush to remove any residual impurities if necessary.
11. Proceed in the opposite order to reassemble all the parts.
ATTENTION
: the place designated for this operation must comply with current environmental
protection regulations.
3
2
3
2
Back
0000.00
100%
1
1
5
5
6
4
4
6
8
8
9
9
7
7
9
9
CLEANING THE VACUUM TUBE
Careful cleaning of the vacuum hose guarantees better cleaning of the floor as well as a longer vacuum
motor life. Proceed as follows to clean the vacuum hose:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “
ATTENTION
: users are advised to always wear protective gloves, to avoid the risk of serious
injury to hands.
3. Extract the vacuum tube (1) from the vacuum nozzle on the squeegee body (
Fig.1
).
4. Remove the vacuum tube (1) via the hole on the back of the recovery tank (
Fig.2
).
2
1
1
1
5. The vacuum hose from the retainers present inside the recovery tank.
6. Rinse the inside of the vacuum hose with a jet of running water.
7. Repeat the operations in reverse order to reassemble all the parts.
To clean the vacuum tube with the spray gun kit, proceed as follows:
1. Take the machine to the maintenance area.
2. Using the DS selector on the control display (
Fig.1
), select the “transfer” program” (1).
3. Stand at the back of the machine.
4. Extract the vacuum tube (2) from the vacuum nozzle on the squeegee body (
Fig.2
).
5. Remove the vacuum tube (2) via the hole on the back of the recovery tank (
Fig.3
).
CAUTION
: users are advised to always wear protective gloves, to avoid the risk of serious
injury to hands.
6. Release the tank cleaning accessory (3) (at the back of the machine) from the retainers (
Fig.4
).
7. Activate the optional tank cleaning kit ON/OFF pump by pressing the button (4) on the back of
the machine (
Fig.5
).
CAUTION
: when using the optional tank cleaning kit, you are advised to always wear goggles
to avoid any risk of serious injury to your eyes.
NB
: before activating the optional tank cleaning kit, check the level indicator (5) to see how
much solution there is in the recovery tank (
Fig.6
).
8. Activate the solution jet by pressing the lever in the tank cleaning accessory.
NB
: to adjust the solution jet from the
tank cleaning accessory, turn the knob (6) on the
accessory itself
(
Fig.7
).
NB
: to adjust the intensity of the solution jet from the
tank cleaning accessory, turn the knob (7)
on the accessory itself
(
Fig.8
).
NB
: to stop the solution jet,
use the lever (8) on the tank cleaning accessory (
Fig.9
).
N.B.
: the place designated for this operation must comply with current environmental protection
regulations.
9. The vacuum hose from the retainers present inside the recovery tank.
10. Rinse the inside of the vacuum hose with a jet of running water.
11. Repeat the operations in reverse order to reassemble all the parts.
DRIVE
0000.00
100%
1
1
3
2
2
2
4
5
6
3
4
5
9
8
8
7
7
6
33
