N.B. :
if you reverse with this program active, the squeegee support is put in the rest position
(raised off the floor) and the vacuum motor is switched off with the relative delay.
The icons that could be visible are:
1. FFM symbol, if visible it shows that the system is operating.
2. FSS symbol, if visible it shows that the system is operating.
3. Side brush/es, if visible it shows that the side brush/es is/are enabled.
4. Working lights symbol, if visible it shows that the working lights are on.
5. General alarm symbol.
ATTENTION
: if visible stop the machine, to continue working (read the paragraph “
6.
Recovery tank full float symbol,
ATTENTION
: if visible it shows that the solution level in the tank has a reached a level beyond
which the vacuum motor might be compromised, therefore the tank needs to be emptied before
continuing the work (read the section “
”).
7.
Solution tank float symbol.
ATTENTION
: if visible it shows that the detergent solution in the tank has a reached a level
beyond which the solenoid valve might not deliver solution onto the brushes, therefore the tank
needs to be filled up before continuing the work (read the section “
8. Eco-Mode button.
N.B.
: if you press the Eco-Mode button (8) you start the working program currently in use in
economic mode, to remove the economic mode read the section “
”.
9. Menu button.
10. Rear camera button.
N.B.
: pressing the rear camera button (10) if present the video camera on the back of the
machine will start, read the section “
” to continue working.
11. Text indicator.
N.B.
: in the text indicator (11) it is possible to see that the zone program has been selected or
whether you are in transport mode if there is the word “DRIVE”.
N.B.
: If you need to activate the dipped headlights when working, read the section “
”.
ATTENTION: The drying without scrubbing operation should only be
carried out if the device was used beforehand to carry out a scrubbing
without drying operation.
ATTENTION: never switch off the machine with the squeegee in
contact with the floor
SCRUBBING WITH DRYING
OFFICE
0000.00
100%
9
10
8
12
11
1
5
2
6
3
7
4
By selecting the "SCRUBBING WITH DRYING” program, the command display screen will appear as
in the adjacent figure.
N.B.
: with this working program pressure on the drive pedal brings the brush heads and the
squeegee to the work position (in contact with the floor). When the drive pedal is pressed, all
the motors are powered. The brush head solenoid valve and the water system pump are
powered up (only if the detergent solution is other than zero).
N.B.
: in the DS selector the scrubbing with drying program (D) is green.
N.B.
: the grey symbols show working programs that are not active. the green symbols show
working programs that are active.
N.B.
: when the drive pedal is released all the brush head motors and the vacuum motor stop
with the respective delays. After the “Reset Delay”time all the brush heads and the squeegee
body are taken to the rest position (raised off the floor). by pressing the forward movement pedal
it will start working with the same program and with the same parameters that were set before it
stopped.
N.B. :
if you reverse with this program active the brush head will remain in contact with the floor,
the motor will continue working but the solenoid valve will not deliver the detergent solution to
the brushes. The squeegee support is put in the rest position (raised off the floor) and the
vacuum motor is switched off with the relative delay.
The icons that could be visible are:
1. FFM symbol, if visible it shows that the system is operating.
2. FSS symbol, if visible it shows that the system is operating.
3. Side brush/es, if visible it shows that the side brush/es is/are enabled.
4. Working lights symbol, if visible it shows that the working lights are on.
5. General alarm symbol.
ATTENTION
: if visible stop the machine, to continue working (read the paragraph “
”).
6.
Recovery tank full float symbol,
ATTENTION
: if visible it shows that the solution level in the tank has a reached a level beyond
which the vacuum motor might be compromised, therefore the tank needs to be emptied before
continuing the work (read the section “
”).
7.
Solution tank float symbol.
ATTENTION
: if visible it shows that the detergent solution in the tank has a reached a level
beyond which the solenoid valve might not deliver solution onto the brushes, therefore the tank
needs to be filled up before continuing the work (read the section “
”).
8. Eco-Mode button.
N.B.
: if you press the Eco-Mode button (8) you start the working program currently in use in
economic mode, to remove the economic mode read the section “
9. Menu button.
10. Rear camera button.
N.B.
: pressing the rear camera button (10) if present the video camera on the back of the
machine will start, read the section “
” to continue working.
11. Zone button
N.B.
: if you need to change the program used when working, press the Zone button (11) (read
the section “
12. Text indicator.
N.B.
: in the text indicator (11) it is possible to see that the zone program has been selected or
whether you are in transport mode if there is the word “DRIVE”.
N.B.
: If you need to activate the dipped headlights when working, read the section “
N.B.
: If the side brush need to be used when working read the paragraph “
”.
ATTENTION: never switch off the machine while the squeegee and/
or brush head is in contact with the floor
ECO MODE
In the centre of the DS selector there is the ECO-MODE key (1). Press it to activate the "ECO-MODE"
program, which provides the best possible performance in terms of consumption and cleaning. To
activate the ECO-MODE program, proceed as follows:
1. Sit on the driver’s seat.
2. Insert the key (1) into the main switch on the control panel. Set the main switch to "I" (
Fig.1
).
3. Select the ECO-MODE working program with the button (2) at the centre of the DS selector
(
Fig.2
).
N.B.
: the grey ECO-MODE key means that the eco mode is not active. A green ECO-MODE
key means that economic mode is active. In addition, when ECO-MODE is active, on the text
indicator row (3) on the display, the words “ECO mode” will appear (
Fig.2
).
N.B. :
pressing the button (2) on the DS selector (
Fig.2
) will activate the SCRUBBING WITH
DRYING program. If you wish to use another working program, select it using the DS selector
ECO mode
0000.00
100%
2
5
3
2
1
1
ON
22
