8. Repeat the operations in reverse order to reassemble all the parts.
To clean the recovery tank with the spray gun kit, proceed as follows:
1. Take the machine to the maintenance area.
2. Using the DS selector on the control display (
Fig.1
), select the “transfer” program” (1).
3. Stand at the back of the machine.
4. Grip the moulded handles (2) on the recovery tank cover (
Fig.2
).
5.
Turn the recovery tank cover until the support (3) fixed to the recovery tank is coupled with the
pin (4) fixed to the recovery tank cover (
Fig.3
).
CAUTION
: users are advised to always wear protective gloves, to avoid the risk of serious
injury to hands.
6. Release the tank cleaning accessory (5) (at the back of the machine) from the retainers (
Fig.4
).
7. Activate the optional tank cleaning kit ON/OFF pump by pressing the button (6) on the back of
the machine (
Fig.5
).
CAUTION
: when using the optional tank cleaning kit, you are advised to always wear goggles
to avoid any risk of serious injury to your eyes.
N.B.
: Before starting the optional tank cleaning kit, check the level indicator (7) to see how
much solution there is in the solution tank (
Fig.6
).
8. Activate the solution jet by pressing the lever in the tank cleaning accessory. Make sure the jet is
pointing into the tank before pressing the lever.
N.B.
: to adjust the solution jet from the
tank cleaning accessory, turn the knob (8) on the
accessory itself
(
Fig.7
).
N.B.
: to adjust the intensity of the solution jet from the
tank cleaning accessory, turn the knob
(9) on the accessory itself
(
Fig.8
).
N.B.
: to stop the solution jet,
use the lever (10) on the tank cleaning accessory (
Fig.9
).
9.
Remove the recycle filter (11), only valid for FLR versions (
Fig.10
).
10.
Rinse the recycle filter (11) thoroughly under the jet of the tank cleaning accessory.
N.B.
: Use a spatula to eliminate any dirt that is particularly difficult to remove.
11. Rinse the inside of the recovery tank, if necessary use a spatula to remove the sludge that has
accumulated at the bottom of the tank.
WARNING
: Be sure to also clean the electro-mechanical float (12) inside the tank (
Fig.12
).
12. Repeat the operations in reverse order to reassemble all the parts.
4
5
DRIVE
0000.00
100%
3
1
2
2
3
4
1
4
5
6
5
6
7
9
10
8
9
7
8
11
12
10
11
EMPTYING THE SOLUTION TANK
Proceed as follows to empty the solution tank:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “
CAUTION
: users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.
3.
Close the tap's output flow, and shift the knob (1) on the left hand side of the steering column
(
Fig.1
) downward.
4. Open the machine's left lateral hatch (2) (
Fig.2
).
5.
Remove the detergent solution filter cap (3) (
Fig.3
).
6.
Open the tap's output flow, and shift the knob (1) on the left hand side of the steering column
upward.
N.B.
: the place designated for this operation must comply with current environmental protection
regulations.
7. When the solution tank is empty, repeat the operations in the reverse order to reassemble all the
parts.
2
3
1
1
2
3
CLEANING THE WATER SYSTEM FILTER
In order to clean the water system's filter, do the following:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “
CAUTION
: users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.
3.
Close the tap's output flow, and shift the knob (1) on the left hand side of the steering column
(
Fig.1
) downward.
4. Open the machine's left lateral hatch (2) (
Fig.2
).
5.
Unscrew the detergent solution filter cap (3) (
Fig.3
).
6.
Rinse the filter cartridge under a jet of water, and use a brush to eliminate any impurities, if
necessary.
N.B.
: the place designated for this operation must comply with current environmental protection
regulations.
7.
Once the filter cartridge is clean, repeat the operations in the opposite order to reassemble all
the parts.
N.B.:
For the sweeping versions, the water system filter is located on the right of the machine.
2
3
1
1
2
3
CLEANING THE DEBRIS HOPPER (SWEEPING VERSION)
To clean the debris hopper, proceed as follows:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “
CAUTION
: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
3. Open the machine's left lateral carter (1) (
Fig.1
).
4. Release the debris hopper locking pin (2) (
Fig.2
).
5. Use the handle (3) to extract the debris hopper (
Fig.3
) and empty it.
N.B.
: the place designated for this operation must comply with current environmental protection
regulations.
6. Clean the inside with a jet of water, and use a brush to remove any residual impurities if necessary.
7. Proceed in the opposite order to reassemble all the parts.
2
3
1
2
1
3
32
