EXTRA BRUSH HEAD PRESSURE
This machine is capable of increasing the pressure exerted upon the brushes during the work cycle.
This can be done in the following manner:
1.
Check that the brush head body is in contact with the floor. If it isn't, use the DS selector to select
“SCRUBBING WITH DRYING” or “SCRUBBING WITHOUT DRYING” (
Fig.1
).
2. Press the “EXTRA PRESSURE ACTIVATION - DEACTIVATION” button (1) on the control
handlebars (
Fig.2
).
3. Press the dead man's lever (2) (
Fig.3
) to start the working cycle.
NB
: as soon as the button (1) is pressed, the control display will show the “POWER” screen
(
Fig.4
). In the middle of the screen there is a graphic symbol (3) and a numeric symbol (4) that
represent a countdown.
NB
: when the extra-pressure function is activated, the countdown starts. During this time, a
pressure stronger than the standard pressure is exerted on the brush head body.
NB
: at the end of the countdown, you return to the working screen that was previously used
and the pressure on the brush head goes back to standard.
HILLYARD DOSING CONTROL (HDC) SYSTEM
Upon request, the machine can be fitted with HILLYARD DOSING CONTROL (HDC), a system that
allows the detergent and water in the solution tank to be measured out separately.
To activate it, proceed as follows.
1. With the machine on, press the menu button (1) on the working screen (
Fig.1
).
2.
Press the HDC system activation/deactivation button (2) (
Fig.2
).
NB
: if the symbol (2) is grey, the HDC system is not active; if the symbol (2) is green, the HDC
system is active.
NB
: to quit the menu screen, wait a short time without pressing anything, or else press on any
point of the display (except one of the displayed buttons).
NB
: the HDC system is activated when the electric pump in the machine water system starts
up.
NB
: if the HDC system is activated, the relative symbol (3) is displayed in the working screen.
NB
: if you want to deactivate the HDC system, press the button (2) again.
ATTENTION
: before starting any work, remember to start up the HDC system.
NB
: to return to the working screen, press on any point of the screen (except the edges of the
display) or else wait three seconds without touching anything.
TUTORIAL
The machine function board contains a memory card with lessons that explain:
•
the first machine start-up.
•
routine maintenance to be carried out on the machine.
•
the machine use and maintenance manual.
To activate them, proceed as follows.
1. With the machine on, press the menu button (1) on the working screen (
Fig.1
).
2. Press the TUTORIAL button (2) (
Fig.2
).
NB
: to return to the working screen, press on any point of the screen (except the edges of the
display) or else wait three seconds without touching anything.
3. On the tutorial screen (
Fig.3
), select the topics you want to study:
A. Using the machine.
B. Daily maintenance.
C. Extraordinary maintenance.
NB
: select the “USING THE MACHINE” key (A) to see the video explaining the stages for
preparing the machine for work (
Fig.3
).
NB
: select the “DAILY MAINTENANCE” key (B) to see the video explaining the maintenance to
be carried out every day (
Fig.3
). When this button is selected, the screen regarding the
selection of the videos to view will be displayed (
Fig.4
). You can view the following tutorial
videos:
•
Draining and cleaning the recovery tank.
•
Cleaning the vacuum tube and squeegee body.
•
Cleaning the vacuum motor filter.
•
Draining and cleaning the solution tank and water system filter.
NB
: select the “EXTRAORDINARY MAINTENANCE” key (C) to see the video explaining the
maintenance to be carried out daily (
Fig.3
). When this button is selected, the screen regarding
the selection of the videos to view will be displayed (
Fig.4
). You can view the following tutorial
videos:
•
Replacing the squeegee rubber blades.
•
Replacing the brush head brushes.
•
Adjusting the squeegee rubber blades.
EMERGENCY SWITCH
This machine is equipped with an emergency switch. To activate it, just press the button (1) on the
back of the control handlebars (
Fig.1
).
WARNING
: this control interrupts the electrical circuit between the batteries and the machine
system.
NB
: after stopping and resolving the problem, turn the key to “0”, set the button (1) to the
standard position and turn the key to “I” to resume the work.
HOUR METER
The control display is in the control panel. At the centre top, you can see the total time the machine
has been used.
The numbers before the "." symbol identify hours, while the number after it indicates hour decimals (an
hour decimal corresponds to six minutes).
When the “hour glass” symbol (1) is flashing, it indicates that the hour meter is counting the appliance
operating time.
BATTERY CHARGE LEVEL INDICATOR
The control display is in the control panel. At the centre top, you can see the battery charge level.
The indicator is composed of two charge level symbols, the first represented by a graphic symbol (2)
and the second by a number indicating the charge percentage (3).
With a low charge level, the graphic symbol (2) will start to flash and after a few seconds it will switch off.
In these conditions, take the machine to the place where its batteries can be charged.
NB
: a few seconds after the battery charge reaches the critical level, the brush gearmotors
switch off automatically. With the remaining charge, it is possible to complete the drying process
before starting the recharging process.
NB
: a few seconds after the battery charge reaches the discharge level, the vacuum motor
switches off automatically.
20
2
3
2
3
Back
0000.00
100%
POWER
0000.00
100%
1
4
OFFICE
0000.00
100%
ECO mode
0000.00
100%
1
2
2
1
3
OFFICE
0000.00
100%
ECO mode
0000.00
100%
1
2
2
1
VIDEO TUTORIAL
Utilizzo della macchina
Manutenzione giornaliera
Interventi straordinari
Back
3
4
C
B
A
DRIVE
0000.00
100%
3
2
1
1
3
