English
19
▶
Do not use the tool in places where there is a risk of fire or explosion unless the tool is specially approved
for this type of use.
▶
Never drive fasteners into existing holes unless this is recommended by
Hilti
(e.g. DX-Kwik).
Workstation
▶
Keep the workplace tidy. Objects which could cause injury should be removed from the working area.
◁
Untidiness in the working area can lead to accidents.
▶
Make sure that the working area is well lit and well ventilated.
Mechanical safety rules
▶
Do not tamper with or modify the tool or parts of it, especially the piston.
▶
Use only fasteners of a type approved for use with the tool.
Thermal safety rules
▶
Do not exceed the recommended maximum fastener driving rate.
▶
If the tool has overheated, allow it to cool down.
▶
Do not dismantle the tool while it is hot. Allow the tool to cool down.
2.4 Careful handling and use of batteries
▶
Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries.
▶
Do not expose batteries to high temperatures, direct sunlight or fire.
▶
Do not take apart, squash or incinerate batteries and do not subject them to temperatures over 80 °C.
▶
Do not attempt to charge or continue to use damaged batteries.
▶
If the battery is too hot to touch, it may be defective. In this case, place the power tool in a non-flammable
location, well away from flammable materials, where it can be kept under observation and left to cool
down. Contact
Hilti
Service after the battery has cooled down.
3 Description
3.1 Product overview
@
Nosepiece
;
Fastener guide X-FG B3-ME
=
Fastener guide X-FG B3-IF
%
Fastener guide locking mechanism
&
Single-nail selector switch
(
Air vents
)
Belt hook
+
Scaffold hook
§
Safety trigger
/
Grip
:
Release buttons
∙
Charge state indicator
$
Liion battery
£
Nail pusher, locked position
|
Nail pusher release mechanism
¡
Support leg
Q
Magazine
W
Status indicator
E
On/off button
R
Nail pusher, unlocked position
3.2 Intended use
The product is a hand-held, cordless fastening tool for indoor use. It is designed to drive specially
manufactured fasteners (nails) into concrete, steel, masonry, sand-lime block and other materials suitable
for use of the direct fastening technique. The product is also designed to fasten electrical cables with clips
if the appropriate fasteners are used. Use only approved fasteners in combination with their corresponding
fastener guide (see the section headed "Technical data").
The fastening tool, battery and fasteners together form a technical entity. This means that trouble-free
fastening with this fastening tool can be ensured only when the
Hilti
fasteners and chargers and batteries
recommended by
Hilti
are used. The fastening and application recommendations made by
Hilti
apply only
when these conditions are observed.
▶
The fastening tool is for hand-held use only.
▶
Misuse of the fastening tool must be ruled out. Misuse of the fastening tool includes triggering in
single-fastener mode without a nail inserted in the fastener guide, driving nails into very soft materials
(e.g. wood), driving single nails when the tool is set to magazine operation, and driving nails into materials
that are too hard (e.g. high-strength steel or very hard natural stone).
▶
Use only
Hilti
Liion batteries of the B 22 series with this product.
▶
Use only
Hilti
battery chargers of the C 4/36 series to charge these batteries.
Printed: 04.10.2017 | Doc-Nr: PUB / 5377483 / 000 / 01
Summary of Contents for BX 3-ME
