17
en
3. Description
The Hilti DX 462HM and DX 462CM are suitable for
the marking of a wide variety of base materials.
The tool works on the well-proven piston principle
and is therefore not related to high-velocity tools. The
piston principle provides an optimum of working and
fastening safety. The tool works with cartridges of
6.8/11 caliber.
The piston is returned to the starting position and the
cartridges are fed to the firing chamber automatically
by gas pressure from the fired cartridge.
The system permits a high quality mark to be com-
fortably, quickly and economically applied to a variety
of base materials with temperatures up to 50° C for
the DX 462CM and with temperatures up to 800° C
with DX 462HM. A mark can be made every 5 seconds
or roughly every 30 seconds if characters are chan -
ged.
The X-462CM polyurethane and the X-462HM steel
marking heads accept either 7 of the 8 mm type char-
acters or 10 of the 5,6 mm type characters, with
heights of 6, 10 or 12 mm.
As with all powder-actuated tools, the DX 462HM and
the DX 462CM, the X-462HM and X-462CM marking
heads, the marking characters and the cartridges
form a "technical unit". This means that troublefree
marking with this system can only be assured if the
characters and cartridges specially manufactured for
the tool, or products of equivalent quality, are used.
The marking and application recommendations given
by Hilti are only applicable if this condition is
observed.
The tool features 5-way safety – for the safety of the
operator and bystanders.
The piston principle
The energy from the propellant charge is transferred to
a piston, the accelerated mass of which drives the fas-
tener into the base material. As approximately 95 % of
the kinetic energy is absorbed by the piston, the fastener
is driven into the base material at much reduced veloc-
ity (less than 100 m/sec.) in a controlled manner. The
driving process ends when the piston reaches the end
of its travel. This makes dangerous through-shots vir-
tually impossible when the tool is used correctly.
The drop-firing safety device
is the result of coupling
the firing mechanism with the cocking movement. This
prevents the Hilti DX tool from firing when it is dropped
2
1
Warning signs
General
warning
Warning:
hot surface
Obligation signs
Wear eye
protection
Wear a
safety helmet
Wear ear
protection
Symbols
Read the opera-
tion instructions
before use
2. General information
2.1 Signal words and their meaning
WARNING
The word WARNING is used to draw attention to a poten-
tially dangerous situation which could lead to severe
personal injury or death.
CAUTION
The word CAUTION is used to draw attention to a poten-
tially dangerous situation which could lead to minor per-
sonal injury or damage to the equipment or other prop-
erty.
2.2 Pictograms
The numbers refer to the illustrations. The illustra-
tions can be found on the fold-out cover pages. Keep
these pages open while you read the operating instruc-
tions.
In these operating instructions, the designation “the
tool” always refers to the DX 462CM / DX 462HM pow-
der-actuated tool.
Location of identification data on the tool
The type designation and the serial number are printed
on the type plate on the tool. Make a note of this infor-
mation in your operating instructions and always refer
to it when making an enquiry to your Hilti representa-
tive or service department.
Type:
Serial no.:
Summary of Contents for DX462CM
