218
08/2018
www.hilti.group
S-BT-ER, S-BT-EF
*) this items are available only on special request
In order to ensure the exact screw-in depth and a proper compressed sealing washer, the S-BT
studs have to be installed with the appropriate depth gauge. With this tool the screw-in depth
can be adjusted in a range of 0 - 1.5 mm (3 steps, 0.5mm per step). The S-CC BT calibration card
is needed to check the initial stand-off of the S-BT stud and to adjust/calibrate the S-DG depth
gauge. After finding the right adjustment level for the S-DG depth gauge, the gauge can be adjust-
ed and the studs can be installed without additional check of the S-DG depth gauge. The depth
gauge has to be re-adjusted (calibrated) at following times:
• Start of the installation process
• Change of the working position (upwards, downwards, horizontal) and base material (thickness,
strength, type)
• Installer change
• After each packaging respectively after the installation of 100 S-BT studs
The lifetime of the S-DG BT depth gauge is
≥
1000 settings.
The installer is responsible for the correct setting of the S-BT studs.
For the periodical verification of the correct stud stand-off the
S-CG BT check gauge can be used.
6)%7$
D
E
F
6)%7$
76%76
6)&$
6'*%70:/RQJ
6'*%70/RQJ
6'*%70:/RQJ
6&&%7
D
616&ö 0
616
&ö:
616&ö 0
616&ö 0
616
&ö:
PP
õ
PP
PP
PP
PP
1P
IWOE
7RUTXHWRRO;%7õ
1PIWOE
6%70)0$1
6%70):$1
6%70)0$1
6%70)0$1
6%70):$1
E
6)&$
6)&$
F
1P
6)&$
$
$
6%70)000
6%70)::
D
E
[
[
+H[QXWZLWKIODQJH0)
+H[QXWZLWKIODQJH:)
+H[QXWZLWKIODQJH0)
+H[QXWZLWKIODQJH0)
+H[QXWZLWKIODQJH:)
6'*%70:/RQJ
6'*%70/RQJ
6'*%70:/RQJ
S-DG BT mechanical depth gauge
Fastener quality assurance
Fastener selection and system recommendation
Fasteners
Drilling tool
Setting tool Stepped drill bit
Depth gauge
S-BT-ER M8/15 SN 6
SBT 4-A22,
SF BT 18-A
or
SF BT 22-A
SBT 4-A22,
SFC 18-A
or
SFC 22-A
TS-BT 5.5-74 S
S-DG BT M8/15 Long 6
S-BT-EF M8/15 AN 6
S-BT-ER M10/15 SN 6
S-DG BT M10-W10/15 Long 6
S-BT-ER W10/15 SN 6
S-BT-EF M10/15 AN 6
S-BT-EF W10/15 AN 6
Design and functionality of the
mechanical calibration card S-CC BT
Fasteners
Drilling tool
Setting tool
Stepped drill bit +
coating removal
drill bit
Depth gauge
S-BT-ER M10 HC 35*)
SBT 4-A22,
SF BT 18-A
or
SF BT 22-A
SBT 4-A22,
SFC 18-A
or
SFC 22-A
TS-BT 5.5-74 S
TS-BT 15-74 S
S-DG BT M10-W10 HC 6
S-BT-ER W10 HC AWG2*)
S-BT-EF M10 HC 35*)
S-BT-EF W10 HC AWG2*)
S-BT-ER M10 HC 120
TS-BT 5.5-74 S
TS-BT 25-74 S
S-BT-ER W10 HC AWG4/0
S-BT-EF M10 HC 120
S-BT-EF W10 HC AWG4/0