6 Use of the Central Unit
6.1 - Description of the panel
SPEACKER holes
Listening messages and records
LED “POWER”
On
Presence line voltage and battery OK
Flashing
Absence line voltage / error battery
Off
Absence power supply
LED “EXIT”
On
Installation disconnected
Flashing
Timing exit download
Off
Installation connected
LED “ALARM”
On
Installation on alert
Flashing
Timing entry download after detection on
delayed zone
.
Passive infrared detector
When detect a presence the backlight of
keyboard and display are on and
- if programmed - allerts the 1 zone.
LED “MEMORY ”
Flashing
Alarm memory activated
LED “STATUS”
On
Operative Central unit
Slow flashing
Module GSM in activity
Fast flashing
Remote Control
LED “GSM”
A fast flashing every 3 seconds
Module GSM recorded on the network
Other flashings
GSM Activity
LEDs to control the status (4 for XR400GSM), (8 forXR800GSM) zones and 24h
On
Opened Zone
Off
Closed Zone
A fast flashing every second
Excluded Zone
On with a fast disconnection every sec.
Excluded and Opened Zone
Flashing(during displaying,memory)
Alarm Memory
Microphone
Listening environment
Alphanumeric Command keyboard
POWER
ALL
USCITA
ZONA
1
ZONA
2
ZONA
3
ZONA
4
1
4
7
2
5
8
3
6
9
ESC
0
GSM
MEM
STATO
tuv
wxyz
pqrs
OFF
ON
jkl
mno
ghi
abc
def
m i c
5
4
1
7
11
2
3
6
8
9
10
HILTRON
24h
ZONA
5
ZONA
6
ZONA
7
ZONA
8
9
3
5
6
4
7
8
10
11
2
1
45
security
5 - LISTENING ENVIRONMENT
Listening environment is allowed during the phone connection only.
Dial to activate it and to close it.
If you wish to extend the duration of listening for more than a minute, you'll need to dial any button
(but) to extend the duration of listening for another minute.
If you dial the listening stops and you listen to the leading voice again listing all the possible
commands.
If you don't dial and press any button for more than a minute, the phone call ends.
6 - ACTIVATING OUTPUT
This command is available only if you program the INT to function on the command ON/OFF.
Dialling the leading voice indicates:
<Output inactive, press to activate o press asterisk to come back to the former
menu>
Or
<Output active, press to deactivate or press asterisk to come back to the former
menu.>
Activating the output, it appears a voltage of 12 V on the clamp +INT of the central. At the end the leading
voice restarts to indicate the status of the central and lists the options available in the voice menu.
7 - TOTAL INSERTION
This command is available when the central is disconnected only.
Dialling the central tries to execute the command and the voice guide restarts the voice menu that
indicates
<System connected totally>
if the central accepts the command or
<System
disconected>
in case there was no execution of command due to an immediate open
zone and not excluded that impedes the insertion of the system.
8-PARTIAL INSERTION A
Also this command is available when the central is disconnected only.
Dialling you command to the central to insert the system according to the scheme of partialization A.
The voice guide restarts to indicate the status of the central with
<System connected partial A>
if the command is accepted otherwise with
<System
disconnected >
if the command is not executed.If the command fails, you'll need to verify
that the immediate zones included in the scheme of partialization aren't open, impeding,
thus, the connection of the system.
9 - PARTIAL INSERTION B
This command, similar to the previous, is available when the central is disconneted only.
Dial to command to the central the partial insertion B.
If the command is followed by the leading voice, it indicates the new status of the central:
<System connected partial B>.
8
5
9
6
7
9
7
security
44
XR400GSM
- XR
800GSM - Installation guide and use
Use of the central unit