TECHNICAL SPECIFICATIONS
Pureit Ultima Eco Mineral RO+UV+MF
Height
~485 mm
Width
~360 mm
Depth
~311 mm
Weight
~9.5 kg
Flow rate*
Approximately 24 litres per hour
Storage tank capacity
10 litres**
7 -Stage Purifying Technology
Membrane type
Pump type
Diaphragm pump, 24V dc
Thin-film composite spiral wound
% Recovery*
Typically 60%
TDS reduction***
90% (min)
Inlet Water Temperature
10°C to 40°C
Input water pH range
6.5-8.5
Rated Power
60 Watts
Pressure rating
10-30 PSI****
Rated Voltage
100-240V AC 50/60 Hz (Device can withstand voltage
fluctuation from 100 to 300 V AC.)
Material of construction for plastic parts Food safe, non-toxic, engineering grade plastics
Length of Power Cord
1.5 metres
Total Dissolved Solids in input water
Upto 2000 mg/lit
##
Total hardness of input water
500 mg/lit (max.)
Iron in input water
0.3 mg/lit (max.)
###
Turbidity of input water
1NTU (max.)
PP Melt Blown Pre-Sediment Filter, Pre-RO Carbon Filter,
Mesh Filter, Reverse Osmosis Membrane, UV Reactor,
Post-RO Carbon Filter and Micro Filter Membrane
5
Germkill Kit™
Material of construction
Food safe, non-toxic, engineering-grade plastics
Germkill Kit™
Pre-Sediment Filter – 1Number Pre-RO Carbon Filter – 1Number
Antiscalant Cartridge – 1Number RO Membrane – 1 Number
TDS Modulator – 1 Number Integrated Post
MF – 1 Number
Germkill performance standard
Meets stringent international criteria for
microbiologically safe drinking water – e.g.,
Environmental Protection Agency (EPA), USA
* Permeate flow rate and recovery are based on standard test conditions and may vary depending on input water quality, TDS,
pressure and life of Filter elements.
** 10 litres of storage only with running water. Or else 9.2 litres of water dispensing.
*** Input water quality and TDS content are important determinants of output water quality.
**** If input pressure exceeds 30 PSI, please install a company provided pressure reducing valve at an additional cost. If the pressure is
lesser than 5 PSI then you need to buy ‘Pressure enhancing pump’ at an additional cost. Device should not be installed in a house
where input pressure is greater than 60 psi.
# Technical specifications are subject to change or improvement without prior notice.
## In case the TDS is >1000 ppm, a company provided anti-scalant is recommended to be installed, this has to be
purchased at extra cost.
### If the iron content in the input water is more ,it is recommended to install a company provided iron filter.
UNDERSTANDING THE DIGITAL DISPLAY PANEL
Indicator
Indicator Status
Frequency of Indication
Indication
Purity Indicator
Blue bars on the left and
right of the Digital Panel
When there is input water
in the purifier
Tank Full
No light
N/A
Tank is not full
Blue
N/A
Tank is full
SF (Central
bar of the
GKK)
Guided
Alert System
Blue
N/A
Pre-Sediment Filter is safe to use
Central bar of the GKK
circle will blink Blue and
the Call Centre number
(1860-210-1000) will be
displayed on the panel
Blinking for sediment filter
will occur to clean/replace
sediment filter after
approximately 132 hours
of pump running time.You
can either clean SF or call
Pureit helpline to replace
filters at a nominal cost
TANK
FULL
Blue
N/A
GKK is safe to use
Last bar of the GKK
circle blinks, ‘CHANGE
GKK’ blink at the centre
of the panel and the call
centre number ‘1860-210-1000’
illuminated at the bottom
of the panel
Blinking for GKK will
occur to replace filter
after approximately 260
hours of pump running time
GKK life will end soon.
Please contact the
Pureit helpline to
replace your GKK
Last bar of the GKK
circle blinks, ‘CHANGE
GKK’ static at the centre
of the panel and the call
centre number ‘1860-210-1000’
illuminated at the bottom
of the panel
After 275 hours of pump
running time post device
installation
GKK life is completed and must
be replaced. At this point, Auto
Shut O
ff
shuts the water flow
ensuring you don’t drink unsafe
water even by accident
Not visible
N/A
Purifier is safe to use
Red band illuminated
In case of a specific
electrical fault
GKK
Shows the indicative range of TDS in
the input and output water respectively.
The level of these bars will change
depending on the input water
This indicates that the life of the
Pre-Sediment Filter will end soon.
Please get your Pre-Sediment Filter
cleaned/ replaced.* If the sediment
filter is not cleaned/replaced in time,
it may a
ff
ect the performance of the
purifier
Indicates where the fault is in the
purifier. At this point, Auto Shut O
ff
shuts the water flow ensuring you
don’t drink unsafe water even by
accident. Please contact the Pureit
helpline to repair the fault.
~Purity refers to the TDS range of water. TDS (Total Dissolved Solids) indications are measured on the basis of conductivity of
output water and this conductivity depends on 1) mobility of ions 2) valency of ions 3) concentration of ions and 4) the
temperature of water. The display of TDS values is an indicative range and not an absolute value. Purity Indicator will only
function when there is input water in the purifier. In case there is no input water in the purifier, then the Digital Display Panel will
show an error and there will be one band lit on either side of the panel. This is a default state indication and does not reflect the
Purity Level of water. You can see the quality of water through the Purity Indicator only when water is being purified or the
purifier is in use. Quality here refers to the TDS range of water.
#After every 275 hours of pump running time the respective Germkill Kit needs to be changed.
Every 275 hours of pump running time typically gives 6000 litres of purified water under test conditions of 10 PSI input pressure,
750 ppm TDS and 25 °C temperature. Any variations from the test conditions will lead to variations in the ltered life. While the
Germkill Kits and the Sediment Filter have a fixed replacement schedule, you might be required to clean/change the SF in the
interim depending on the quality of your input water.
Pureit Ultima Eco Mineral RO+UV+MF has been designed in such a way that during the first time startup of the device, the
"Tank Full" indicator will blink for 15 minutes (maximum) and then normalise for usage.
T
Extremely low
Very low
Low
Moderate
High
Very high
Low
Moderate
Moderate
High
Very high
Extremely high
TDS range
represented
TDS range
represented
Germkill Kit
TM
Life Indicator
Purity
~
Indicator
Purity
~
Indicator
TDS IN
TDS OUT
ANK
FULL
G
K
K
SF
