Hirschmann GREYHOUND GRS1020 Reference Manual Download

Page: 394 / 619

Specifying the IP parameters

2.7

Management address conflict detection

UM Config GRS

Release

8.0

09/2019

2.7

Management address conflict detection

You assign an IP address to the device using several different methods. This function helps the

device detect IP address conflicts on a network after boot up and the device also checks

periodically during operation. This function is described in RFC 5227.

When enabled, the device sends an SNMP trap informing you that it detected an IP address

conflict.

The following list contains the default settings for this function:

•

Operation

•

Detection mode

active and passive

•

Send periodic ARP probes

marked

•

Detection delay [ms]

200

•

Release delay [s]

•

Address protections

•

Protection interval [ms]

200

•

Send trap

marked

2.7.1

Active and passive detection

Actively checking the network helps prevent the device from connecting to the network with a

duplicate IP address. After connecting the device to a network or after configuring the IP address,

the device immediately checks whether its IP address exists within the network. To check the

network for address conflicts, the device sends 4 ARP probes with the detection delay of 200 ms

into the network. When the IP address exists, the device attemps to return to the previous

configuration, and make another check after the configured release delay time.

When you disable active detection, the device sends 2 gratuitous APR announcements in 2 s

intervals. Using the ARP announcements with passive detection enabled, the device polls the

network to determine whether there is an address conflict. After resolving an address conflict or

after expired release delay time, the device reconnects to the network. Following 10 detected

conflicts, when the configured release delay interval is less than 60 s, the device sets the release

delay interval to 60 s.

After the device performs active detection or you disable the active detection function, with passive

detection enabled the device listens on the network for other devices using the same IP address.

When the device detects a duplicate IP address, it initially defends its address by employing the

ACD mechanism in the passive detection mode and sends out gratuitous ARPs. The number of

protections that the device sends and the protection interval are configurable. To resolve conflicts,

if the remote device remains connected to the network, then the network interface of the local

device disconnects from the network.

When a DHCP server assigns an IP address to the device and an address conflict occurs, the

device returns a DHCP decline message.

The device uses the ARP probe method. This has the following advantages:



ARP caches on other devices remain unchanged



the method is robust through multiple ARP probe transmissions

Summary of Contents for GREYHOUND GRS1020












































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for GREYHOUND GRS1020

Reviews:

Related manuals for GREYHOUND GRS1020

Brands by name

Popular brands

Hirschmann GREYHOUND GRS1020, Reference Manual

Search results

Summary of Contents for GREYHOUND GRS1020

Reviews:

Related manuals for GREYHOUND GRS1020

Brands by name

Popular brands