Step-by-step installation guide
TOP LINE OF REAR WALL TEMPLATE
F.CUT OUT FOR HORIZONTAL
OUTSIDE EXHAUST
CAUTION -IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE
TOP LINE OF REAR WALL TEMPLATE
Front overhang
of cabinet
bottom
Front
Rear
3
.
Beneath framed recesse bottom cabinet with front overhang
TOP LINE OF REAR WALL TEMPLATE
THE MICROWAVE MUST BE LEVEL
F.CUT OUT FOR HORIZONTAL
OUTSIDE EXHAUST
3/8" TO EDGE
30" MINIMUM WIDTH REQUIRED
REAR WALL TEMPLATE
CAUTION -IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION
，
GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE.
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
A
C
B
Your cabinets may have decorative trim that interferes with the
microwave installation. Remove the decorative trim to install the
microwave properly and to make it level.
Use a level to make sure the cabinet bottom is level. If the cabinets have a
front overhang only,with no back or side frame, top line of rear wall template
must align with below cabinet bottom, the same distance as the front overhang
depth.this will keep the microwave level.
1.Measure the inside depth of the front overhang.
2.Draw a horizontal line on the back wall an equal distance below the cabinet
bottom as the inside depth of the front overhang.
3.For this type of installation with front overhang only,align top line of rear wall
template with this horizontal line, not touching the cabinet bottom as described
in step D.
below cabinet bottom the same
distance as the front overhang of
cabinet bottom
11
F.CUT OUT FOR HORIZONTAL
OUTSIDE EXHAUST
3/8" TO EDGE
30" MINIMUM WIDTH REQUIRED
REAR WALL TEMPLATE
CAUTION -IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION
，
GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE.
A
C
B
Must align with below cabinet bottom the same distance as the front overhang of cabinet
bottom.
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLLOW THE DIRECTIONS
IN THE INSTALLIONS INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This template is for locating the horizontal exhaust
cutout .Do not use this temlate for vertical or
recirculation exhaust.
1.Tape the template to the rear wall.
2. Use a saber or keyhole saw to cut out the
shaded area F.through the rear wall.
3. Remove the template from the rear wall.
4. R
eturn to and proceed with the installation
instructions.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTER LINE.
MARK THE LOCATION FOR 2 ADDTIONAL,EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Locate and mark holes to align with holes in the
mounting plate.
6"
12"
4"
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTER LINE.
MARK THE LOCATION FOR 2 ADDTIONAL,EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
This template is for locating the horizontal exhaust
cutout .Do not use this temlate for vertical or
recirculation exhaust.
1.Tape the template to the rear wall.
2. U
se a saber or keyhole saw to cut out the
shaded area F.through the rear wall.
3. Remove the template from the rear wall.
4. R
eturn to and proceed with the installation
instructions.
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLLOW THE DIRECTIONS
IN THE INSTALLIONS INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This template is for locating the horizontal exhaust
cutout .Do not use this temlate for vertical or
recirculation exhaust.
1.Tape the template to the rear wall.
2. U
se a saber or keyhole saw to cut out the
shaded area F.through the rear wall.
3. Remove the template from the rear wall.
4. R
eturn to and proceed with the installation
instructions.
12"
4"
6"
NOTE: IT IS VERY IMPORTANT TO
IN THE INSTALLIONS INSTRUCTIONS
READ AND FOLLLOW THE DIRECTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
