background image

15

 Special Remarks

 Heating (      ) Operation

 Heating performance 

Defrosting

POWER lamp

  Because this air conditioner heats a room by drawing on the heat of  the outside  air  

     (heat pump system), the heating efficiency will fall off when the outdoor temperature

     is very low. If sufficient heat cannot be obtained with this air conditioner, use another 

     heating appliance in conjunction with it.

 When the outdoor temperature is low, frost or ice may  from  in  the  heat  exchanger 

     coil, reducing heating performance. When this happens, a microcomputer defrosting

     system will operate. At the same time the fan on the indoor  unit  stops  ( or  runs  at 

     very low speed in some cases). Heating  operation  restarts  after  several  minutes.

     (This interval will vary slightly depending upon the outdoor temperature and the way

     in which frost forms).

 For several minutes after the start of heating operation, the indoor fan  will  not  start 

     running until the  indoor  heat  exchanger  coil  has  warmed  up  sufficiently.  This  is

     because the COLD DRAFT PREVENTION SYSTEM is operating.

 The POWER lamp also remains lit during defrosting  or  when  the  compressor  has

     been turned off by the thermostat when the system is in the heating mode.

 In the event of power failure, the unit will stop. When the power is resumed, 

     the unit will restart automatically after three minutes.

 In heating or cooling operation. Some plastic parts may expand of   shrink  due  to  a  

    sudden temperature change. In this event, a clicking sound may occur. This is normal,

    and the sound will soon disappear.

 The remote control unit sends the temperature signal to the air conditioner  regularly

     at three-minute intervals. If the signal from the remote control  unit  stops  for   more 

     than ten minutes due to the loss of the remote control unit or  other trouble,   the  air 

     conditioner will switch to the temperature sensor which is built  into  the  indoor  unit

     and  control  the  room  temperature.  In  these  cases,  the temperature around the

     remote control unit may differ from the temperature  detected at the air conditioner

s

     position.

Power failure
during operation

Clicking Sound

Clicking sound is 

heard from the air 

conditioner

Summary of Contents for KFR 2101GWE
























Reviews: