English
9
Optional accessories are subject to change without notice.
Taper shank adapter
Taper mode
Morse taper No.1
Morse taper No.2
A-Taper
B-taper
Drilling anchor holes
Core bit
Center pin
Core bit shank
Outer dia.
Overall length
25 mm*
Not applicable
29 mm*
32 mm
105 mm
35 mm
(A)
300 mm
38 mm
45 mm
(B)
300 mm
50 mm
Large hole boring
Anchor setting adapter
Anchor size
W 1/4”
W 5/16”
W 3/8”
W 1/2”
W 5/8”
Anchor setting
* Without guide plate
APPLICATIONS
Rotation and hammering function
Drilling anchor holes
Drilling holes in concrete
Drilling holes in tile
Rotation only function
Drilling in steel or wood
Tightening machine screws, wood screws
Hammering only function
Light-duty chiselling of concrete, groove digging and
edging.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a power receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause a
serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Mounting the drill bit (Fig. 1)
CAUTION
To prevent accidents, make sure to turn the switch
off and disconnect the plug from the receptacle.
NOTE
When using tools such as bull points, drill bits, etc.,
make sure to use the genuine parts designated by
our company.
(1) Clean the shank portion of the drill bit.
(2) Insert the drill bit in a twisting manner into the tool
holder until it latches itself (Fig. 1).
(3) Check the latching by pulling on the drill bit.
(4) To remove the drill bit, fully pull the grip in the
direction of the arrow and pull out the drill bit (Fig. 2).
5. Installation of dust cup or dust collector (B)
(Optional accessories) (Fig. 3, Fig. 4)
When using a rotary hammer for upward drilling
operations attach a dust cup or dust collector (B) to
collect dust or particles for easy operation.
Drilling holes in concrete or tile
SDS-plus Drill bit
Outer dia.
Overall length
Effective length
4.0 mm
110 mm
50 mm
5.0 mm
110 mm
50 mm
160 mm
100 mm
5.5 mm
110 mm
50 mm
6.5 mm
160 mm
100 mm
7.0 mm
160 mm
100 mm
8.0 mm
160 mm
100 mm
8.5 mm
160 mm
100 mm
9.0 mm
160 mm
100 mm
12.0 mm
166 mm
100 mm
260 mm
200 mm
12.7 mm
166 mm
100 mm
14.0 mm
166 mm
100 mm
15.0 mm
166 mm
100 mm
16.0 mm
166 mm
100 mm
260 mm
200 mm
17.0 mm
166 mm
100 mm
19.0 mm
260 mm
200 mm
20.0 mm
250 mm
200 mm
22.0 mm
250 mm
200 mm
Drill bit (slender shaft)
Outer dia.
Overall length
Effective length
3.4 mm
90 mm
45 mm
3.5 mm
Summary of Contents for DH24PM
