21
PT3-H AVC3-U
AV NETWORK SETUP WIZARD
5.
Follow the steps below to setup the AV network (See page 22 for AV Network Codes).
There are six steps in the setup procedure (VCR setup example below).
HITACHI AV NET SET UP
Proper Code Entered
from page 21.
AV Receiver
PV Recorder
VCR
DVD
Move
POWER
MENU
MORE
INFO
Device Setting
DVD
Device Code
- - - -
(Enter code “9999” to uninstall)
Video Input
No Connection
Audio Input
No Connection
Transmission Test
POWER
PLAY
CH UP
BACK
OK
EXIT
HITACHI AV NET SET UP
DVD
Device Code
0 6 7 2
(Enter code “9999” to uninstall)
Video Input
No Connection
Audio Input
No Connection
Transmission Test
POWER
PLAY
CH UP
BACK
OK
EXIT
Congratulations
Your DVD is now
connected to your AV network.
HITACHI AV NET SETTING LIST
Device
Code
Video
Audio
DVD
0672
INPUT 1
Using TV
VCR
----
Not Setup
Not Setup
PVR
----
Not Setup
Not Setup
AVR
----
Not Setup
Not Setup
CBL
----
Not Setup
Not Setup
STB
----
Not Setup
Not Setup
Custom
----
Not Setup
Not Setup
EXIT
HITACHI AV NET SET UP
DVD
Device Code
0 6 7 2
(Enter code “9999” to uninstall)
Video Input
Input 1
Audio Input
Using TV
Transmission Test
POWER
PLAY
CH UP
BACK
OK
EXIT
Move
SEL Select
Set Input
AV Receiver
PV Recorder
VCR
DVD
POWER
MENU
MORE
Move
INFO
Device Setting
HITACHI AV NET SET UP
DVD
Device Code
0 6 7 2
(Enter code “9999” to uninstall)
Video Input
Input 1
Audio Input
No Connection
Transmission Test
POWER
PLAY
CH UP
BACK
OK
EXIT
Move
SEL Select
Set Input
HITACHI AV NET SET UP
DVD
Device Code
0 6 7 2
(Enter code “9999” to uninstall)
Video Input
Input 1
Audio Input
Using TV
Transmission Test
POWER
PLAY
CH UP
BACK
OK
EXIT
Move
SEL Select
Set Input
HITACHI AV NET SET UP
SEL
Select
Move
0-9
Input
Move
0-9
Input
THUMB
STICK
THUMB
STICK
THUMB
STICK
THUMB
STICK
SELECT
THUMB
STICK
SELECT
THUMB
STICK
(x2)
9
0
6.
To uninstall or change device (equipment), press INFO button on the remote control when the device (DVD, VCR, etc.) is
highlighted.
Enter the device (equipment) code listed on page 22.
Use THUMBSTICK
to select the input that the device (equipment)
is hooked-up to.
Transmission test for the device to confirm that the proper code was
set, by selecting (POWER, PLAY, etc.) soft keys shown. If the device
responds to the transmission test soft key, then it is properly set up.
Select OK to continue.
Summary of Contents for 50HDT50
