Hitachi 55HK5600, Instruction Manual

English

   - 32 -

• 

The location where the transmission is most effective 

differs depending on the usage environment.

• 

The Wireless feature of the TV supports 802.11 a,b,g 

& n type modems. It is highly recommended that 

you should use the IEEE 802.11n communication 

protocol in order to avoid any possible problems 

while watching videos.

• 

You must change your modem’s SSID when there 

are any other modems around with the same SSID. 

You can encounter connection problems otherwise. 

Use a wired connection if you experience problems 

with a wireless connection. 

Configuring Wireless Device Settings

Open the 

Network

 menu and select 

Network Type

 as 

Wireless Device

 to start connection process.

Highlight 

Scan Wireless Networks 

option and press 

OK

 to start a search for available wireless networks. 

All found networks will be listed. Highlight your desired 

network from the list and press 

OK

 to connect. 

Note:

 If the modem supports N mode, you should set N 

mode settings.

If the selected network is password-protected, enter 

the correct key by using the virtual keyboard. You can 

use this keyboard via the directional buttons and the 

OK

 button on the remote control.

Wait until the IP address is shown on the screen.
This means that the connection is now established. 

To disconnect from a wireless network, highlight 

Network Type 

and press Left or Right buttons to set 

as 

Disabled

.

If your router has WPS, you can directly connect to the 

modem/router without entering a password or adding 

the network first.

Highlight 

Press WPS on your wifi 

router

 option and press 

OK

. Go to your modem/router 

device and press the WPS button on it to make the 

connection. You will see a connection confirmation on 

your TV once the devices have paired. Select 

OK

 to 

proceed. No further configuration is required.

Highlight 

Internet Speed Test

 and press the 

OK

 button 

to check your internet connection speed. Highlight 

Advanced

Settings 

and press the 

OK

 button to 

open the advanced setting menu. Use directional and 

numeric buttons to set. Highlight 

Save

 and press the 

OK

 button to save settings when complete. 

Other Information

The status of the connection will be displayed as 

Connected

 or 

Not

Connected

 and

the current IP 

address, if a connection is established.

Connecting to your mobile device via WLAN

• 

If your mobile device has WLAN feature, you can 

connect it to your TV via a router, in order to access 

the content in your device. For this, your mobile 

device must have an appropriate sharing software.

  Connect your TV to your router following the steps 

mentioned in the sections above.

  Afterwards, connect your mobile device to the router 

and then activate the sharing software on your mobile 

device. Then, select files that you want to share with 

your TV.

  If the connection is established correctly, you will 

be able to access the shared files installed on your 

mobile device via the AVS(audio video sharing) 

feature of your TV.

  Highlight the 

AVS

 option in the 

Sources

 menu and 

press 

OK

, available media server devices in the 

network will be displayed. Select your mobile device 

and press the 

OK 

button to continue.

• 

If available, you can download a virtual remote 

controller application from the server of your mobile 

device application provider. 

Note: 

This feature may not be supported on all mobile 

devices.

Wake ON

Wake-on-LAN (WoL) and Wake-on-Wireless LAN 

(WoWLAN) are standards that allow a device to be 

turned on or woken up by a network message. The 

message is sent to the device by a program executed 

on a remote device connected to the same local area 

network, such as a smartphone. 
Your TV is WoL and WoWLAN compatible. This feature 

might be disabled during the First Time Installation 

process. To enable this feature set the 

Wake On

 option 

in the 

Network 

menu as 

On

. It is necessary that both 

the device, from which the network message will be 

sent to the TV, and the TV are connected to the same 

network. Wake On feature is only supported for Android 

OS devices and can only be used via YouTube and 

Netflix applications.

In order to use this feature the TV and the remote 

device should be connected at least once while the 

TV is on. If the TV is powered off, the connection 

should be re-established, the next time it is switched 

on. Otherwise this feature will be unavailable. This 

does not apply, when the TV is switched into the 

standby mode.
If you want your TV to consume less power in standby 

mode, you can disable this feature by setting the 

Wake 

On

 option as 

Off

.

Wireless Display

Wireless Display is a standard for streaming video and 

sound content. This feature provides the ability to use 

your TV as wireless display device.

Using with mobile devices

There are different standards which enable sharing of 

screens including graphical, video and audio content 

between your mobile device and TV.