10
RADIO TUNER OPERATION
RADIO TUNER OPERATION
RADIO TUNER OPERATION
RADIO TUNER OPERATION
RADIO TUNER OPERATION
L i s t e n i n g t o R a d i o
L i s t e n i n g t o R a d i o
L i s t e n i n g t o R a d i o
L i s t e n i n g t o R a d i o
L i s t e n i n g t o R a d i o
Please note : Connect the pigtale aerial in the 75ohm Antenna socket on the
back of the unit
1. Press TUNER/BAND button to select FM or MW mode. On the remote, press
BAND button to select FM or MW mode.
2. Press
or
to select a radio station.
N o t e :
N o t e :
N o t e :
N o t e :
N o t e :
• If you press
or
for less than three seconds each time, the receiving
frequency moves up or down incrementally.
• If you press and hold
or
for more than three seconds, the frequency
continues to increase automatically until a radio station is received.
3. Adjust to the desired sound and volume.
N o t e :
N o t e :
N o t e :
N o t e :
N o t e :
The last tuned station is retained and recalled when you turn the system on. The
tuned station is stored into memory even if power is disconnected or cut due to
temporary power failure.
S e t t i n g R a d i o S t a t i o n s i n t o M e m o r y
S e t t i n g R a d i o S t a t i o n s i n t o M e m o r y
S e t t i n g R a d i o S t a t i o n s i n t o M e m o r y
S e t t i n g R a d i o S t a t i o n s i n t o M e m o r y
S e t t i n g R a d i o S t a t i o n s i n t o M e m o r y
You may store up to 20 FM stations and 20 MW stations in channel memory.
1. Press TUNER/BAND button to select FM or MW mode. On the remote, press
BAND button to select FM or MW mode.
2. Press
or
to select a radio station.
3. Press PROG/MEM button, "PROGRAM" flashs on the display.
4. Press "" or "PRESET -" to selet program channel.
5. Press PROG/MEM button to save into memory. If it has been previously set,
the former station is replaced.
6. Repeat steps 2 to 5 to store additional stations.
P l a y i n g P r e s e t S t a t i o n s
P l a y i n g P r e s e t S t a t i o n s
P l a y i n g P r e s e t S t a t i o n s
P l a y i n g P r e s e t S t a t i o n s
P l a y i n g P r e s e t S t a t i o n s
1. Press TUNER/BAND button to select FM or MW mode. On the remote, press
BAND button to select FM or MW mode.
2. Press /– to select the desired preset channel.
I m p r o v i n g R e c e p t i o n
I m p r o v i n g R e c e p t i o n
I m p r o v i n g R e c e p t i o n
I m p r o v i n g R e c e p t i o n
I m p r o v i n g R e c e p t i o n
M W R e c e p t i o n
M W R e c e p t i o n
M W R e c e p t i o n
M W R e c e p t i o n
M W R e c e p t i o n
Reposition the unit to get better MW reception.
N o t e :
N o t e :
N o t e :
N o t e :
N o t e : Do not connect to an outside antenna.
F M R e c e p t i o n
F M R e c e p t i o n
F M R e c e p t i o n
F M R e c e p t i o n
F M R e c e p t i o n
1. Plug in supplied FM wire antenna to the FM antenna socket of this unit, fully
unwind the FM wire antenna and position it for best FM signal reception. OR
2. Connect a FM antenna cable (not supplied) from FM antenna socket of this
unit to your home FM antenna socket.
