12
English
(2) Avoid recharging at high temperatures.
A back pack power supply will be hot immediately after
use. If such a back pack power supply are recharged
immediately after use, its internal chemical substance
will deteriorate, and the back pack power supply life will
be shortened. Leave the back pack power supply for a
while, and recharge them after they have cooled.
CAUTION
○
If the back pack power supply are charged while it is
heated because it has been left for a long time in a
location subject to direct sunlight or because the back
pack power supply have just been used, the pilot lamp
of the charger lights up green. In such a case,
fi
rst let
the back pack power supply cool, then start charging.
○
When the charge status
fl
ickers in red (at 0.2-seconds
intervals), check for and take out any foreign objects in
the charger’s battery connector. If there are no foreign
objects, it is probable that the back pack power supply
or charger is malfunctioning. Take it to your authorized
Service Center.
○
Since the built-in microcomputer takes about 3 seconds
to con
fi
rm that the back pack power supply being
charged with UC36YRSL is taken out, wait for a minimum
of 3 seconds before reinserting it to continue charging.
If the adapter of back pack power supply is reinserted
within 3 seconds, the back pack power supply may not
be properly charged.
USED
AS
A
POWER
SUPPLY
FOR
CORDLESS
POWER
TOOLS
(DC
36V)
WARNING
○
Read the instruction manuals for power tools that are to
be connected beforehand.
○
Always check to con
fi
rm that cordless power tools are
switched o
ff
before connecting them to the Back Pack
Power Supply adapter.
1.
Check
to
con
fi
rm
that
the
main
switch
is
o
ff
.
(Fig.
8)
The main switch is o
ff
if the green power indicator is not
illuminated when the power switch on the switch panel
is pressed.
2.
Put
on
the
Back
Pack
Power
Supply.
Tighten the chest buckle and waist buckle so that there
is no looseness but still easy to move. Then adjust the
length of the band and strap.
3.
Check
to
con
fi
rm
that
the
cordless
power
tool
to
be
connected
is
switched
o
ff
.
• Plugging the adapter into the power tool adapter
with the switch set at on may result in unexpected
operations, leading to injury.
• Check that the switch to the power tool returns to the o
ff
position when pulled once.
4.
Plug
the
adapter
into
the
cordless
power
tool.
(Fig.
8)
Insert the adapter
fi
rmly until it clicks into place in the
same way as the battery.
5.
Switch
on
the
main
switch
and
power
switch
to
the
Back
Pack
Power
Supply.
Switch on the Back Pack Power Supply’s main switch.
Then switch on the power switch on the switch panel
to illuminate the power indicator and supply DC 36V of
electrical current to the cordless power tool connected.
6.
Switch
on
the
cordless
power
tool
and
begin
work.
Carry out the required work in accordance with the
details provided in the instruction manual for the
cordless power tool in use.
7.
Check
the
remaining
capacity
of
the
battery.
Press the remaining battery capacity switch on the
switch panel periodically and check the indicator to
avoid the power tool from stopping midway through the
work in hand.
8.
Terminating
electricity
supply.
Switch
o
ff
the cordless power tool in use, and then
switch o
ff
the power switch and main switch to the Back
Pack Power Supply.
Automatic
power
o
ff
function
(power
switch
on
the
switch
panel)
To prevent the wasteful use of the Back Pack Power
Supply, the power will be automatically switched o
ff
after
fi
ve hours elapses without it being used with the
power switch on the switch panel left in the on position.
If the main switch is left on, check to con
fi
rm that the
power to the cordless power tool or USB device being
used is switched o
ff
before pressing the power switch
on the switch panel to resume work.
SWITCH
PANEL
DISPLAYS
(FIG.
9)
Power
Switch
The power indicator will be illuminated in green and DC
36V of electrical current will be supplied to the adapter
when the power switch is pressed with the main switch
to the Back Pack Power Supply at the on position.
Remaining
Battery
Capacity
Switch
Press the remaining capacity switch to discover the
remaining capacity with the indicator that is illuminated
in red through
fi
ve stages.
If the indicator on the right blinks, it means the battery
has run out and output has ceased. Recharge the
battery in this event.
Warning
Indicator
Noti
fi
es the user that output has been halted owing to a
problem arising.
(Continual
illumination
in
red)
Carrying out work that constantly requires large
amounts of electrical current and that involves
continual use under harsh conditions, such
as high-temperature environments, will cause
the temperature inside the Back Pack Power
Supply to rise. Output will be halted in this
event to prevent high-temperature damage.
Wait until the Back Pack Power Supply cools
down before resuming work.
(Blinking
in
red)
Output will be halted to prevent damage in the
event of overloaded operations caused by the
blades in cordless power tools, etc., continuing.
Resolve the reason for the overload, and then
press the power switch to resume operations.
(Swift
blinking
in
red)
There is a possibility that damage has
occurred. Cease operations immediately and
request inspections or repairs.
USED
AS
A
USB
POWER
SUPPLY
(DC
5V)
WARNING
○
Read the instruction manual for the USB device to be
connected beforehand.
○
Check to con
fi
rm that the USB cable to be connected is
not damaged before using it.
Failure to observe this may result in the outbreak or
smoke or
fi
re.
○
Seal the USB terminal with a rubber cover when not in use.
If dust or other matter adheres to the USB terminal, it
may result in the outbreak of smoke or
fi
re.
000Book̲BL36200̲EE.indb 12
000Book̲BL36200̲EE.indb 12
2013/03/20 13:42:08
2013/03/20 13:42:08
