60
Maintenance
1.
Turn the projector off, and unplug the power cord. Allow the
SURMHFWRUWRFRROVXI¿FLHQWO\
2.
After making sure that the projector has cooled adequately,
slowly turn over the projector, so that the bottom is facing.
3.
Remove the battery cover.
Turn the battery cover in the direction indicated “OPEN”
using such as coins. Then the battery cover will come up. While
removing the battery cover, pick its knob.
4.
Take the old battery out.
Press the metal claw of the battery holder. Then the battery
will come up. Remove the battery.
5.
Put a new battery in.
Replace battery with HITACHI MAXELL, Part No.CR2032
RQO\8VHRIDQRWKHUEDWWHU\PD\SUHVHQWDULVNRI¿UHRU
explosion.
Insert a new battery in the battery holder according to its minus terminal
as indicated in the battery holder, so that the side marked by + is
IDFLQJ$QGSXVKWKHEDWWHU\LQWRWKHEDWWHU\KROGHUIXOO\WR¿[
6.
Close the battery cover.
Replace the battery cover in place, then turn it in the
GLUHFWLRQLQGLFDWHG³&/26(´XVLQJVXFKDVFRLQVWR¿[
%.15'
Battery Cover
12'0
Knob
Metal claw
“+” marking
WARNING
Ź
Always handle the batteries with care and use them only as directed. Battery
PD\H[SORGHLIPLVWUHDWHG'RQRWUHFKDUJHGLVDVVHPEOHRUGLVSRVHRILQ¿UH
$QGDOVRLPSURSHUXVHPD\UHVXOWLQFUDFNLQJRUOHDNDJHZKLFKFRXOGUHVXOWLQ¿UHLQMXU\DQGRU
pollution of the surrounding environment.
•
%HVXUHWRXVHRQO\WKHEDWWHULHVVSHFL¿HG'RQRWXVHEDWWHULHVRIGLIIHUHQWW\SHVDWWKHVDPH
time. Do not mix a new battery with used one.
• Make sure the plus and minus terminals are correctly aligned when loading a battery.
If the battery is placed in the battery holder upside-down, it may be hard to remove.
• Keep a battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.
• Do not short circuit or solder a battery.
•
'RQRWDOORZDEDWWHU\LQD¿UHRUZDWHU.HHSEDWWHULHVLQDGDUNFRRODQGGU\SODFH
•
,I\RXREVHUYHDOHDNDJHRIDEDWWHU\ZLSHRXWWKHÀRZHUDQGWKHQUHSODFHDEDWWHU\,IWKHOLTXLG
adheres to your body or clothes, rinse well with water immediately.
• Obey the local laws on disposing the battery.
Internal clock battery
Consumption of the battery makes the clock not to work correctly. When the clock is wrong or it has
stopped, please replace the battery according to the following procedures.
NOTE
• If the battery is placed in the battery holder upside-down, follow the procedure below
to remove and reload it properly.
1. Remove the battery cover as described in steps 1 through 3 above.
2. Turn the projector over again, so that the top of the projector is facing up.
3. While lifting the side of the projector closest to the lens, press the metal claw of the battery
holder. The battery will fall out of the holder, so be careful not to lose it.
4. Turn the projector over once more, so that the bottom faces up, and reload the battery correctly.
• The internal clock’s time will be reset when the battery is removed.
3OHDVHUHFRQ¿JXUHWKHWLPHYLDWKHPHQXRUDZHEEURZVHUDIWHUUHSODFLQJWKHEDWWHU\
(Please refer to
55
and User’s Manual-Network Functions: Date/Time Settings for more information.)
