6
English
DRILL SAFETY WARNINGS
1.
Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
2.
Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord.
Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
3. Hold the drill securely when using.
4. Do not wear gloves made of stuff liable to roll up
such as cotton, wool, cloth or string, etc.
5. Prior to drilling into walls, ceilings or floors, ensure
there are no electric cables or conduits inside.
6. Do not use the tool for tightening or loosening of
screws, bolts, etc.
Doing so may cause damage to the tool or personal
injury.
STANDARD ACCESSORIES
䡬
Chuck wrench (Spec. only for keyed chuck) ..... 1
Standard accessories are subject to change without notice..
APPLICATIONS
䡬
Boring holes in metal, wood and plastic.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, inviting serious
accident.
3. Extension cord
When the work area is removed from the power
source. Use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Selecting the appropriate drill bit:
䡬
When boring metal or plastic
Use ordinary metalworking drill bits.
䡬
When boring wood
Use ordinary woodworking drill bits.
However, when drilling 6.5 mm or smaller holes,
use a metalworking drill bit.
5. Mounting and dismounting of the bit
For keyed chuck
(Fig. 1)
(1) Open the chuck jaws, and insert the bit into the
chuck.
(2) Place the chuck wrench in each of the three holes
in the chuck, and turn it in the clockwise direction
(viewed from the front side). Tighten securely.
(3) To remove the bit, place the chuck wrench into one
of the holes in the chuck and turn it in the
counterclockwise direction.
For keyless chuck
(Fig. 2)
(1) Open the chuck jaws, and insert the bit into the
chuck.
To open the chuck jaws, hold the ring while turning
the sleeve in the counterclockwise direction (viewed
from the front side).
(2) Firmly grasp the ring and turn the sleeve in the
clockwise direction. Tighten securely.
(3) To remove the bit, firmly grasp the ring and turn
the sleeve in the counterclockwise direction.
(4) If it is hard to loosen the sleeve, fix the spindle
using the open-end wrench, hold the sleeve firmly,
and turn it in the loosening direction
(counterclockwise when viewed from the front).
(
Fig. 3
)
6. Check the rotational direction (Fig. 4)
The bit rotates clockwise (viewed from the rear
side) by turning the rotational change lever to R-
mark.
The rotational change lever is returned to the L-
mark to turn the bit counterclockwise.
(The
L
and
R
marks are provided on the body.)
7. RCD
The use of a residual current device with a rated
residual current of 30mA or less at all times is
recommended.
SPECIFICATIONS
Voltage (by areas)*
(110 V, 220 V, 230 V, 240 V)
Power input
450 W*
No load speed
0 – 3200 min
–1
Drill chuck capacity
10 mm
Capacity
Steel
10 mm
Wood
25 mm
Weight (without cord)
1.2 kg
*Be sure to check the nameplate on product as it is subject to change by areas.
01Eng_D10VST_WE
2/1/12, 13:15
6
