13
English
Table 4
These data are for the referential values. The number of
holes that can be drilled varies according to the sharpness
of the used bit or the conditions of the concrete being
drilled.
CAUTION:
When using this unit continuously, the unit may
overheat, leading to damage in the motor and switch.
Please leave it without using it for approximately
15 minutes.
HOW TO USE
1. Switch operation
䡬
When the switch trigger is depressed, the tool
rotates. When the switch trigger is released, the
tool stops.
䡬
The rotational speed of the rotary hammer can be
controlled by varying the amount that the switch
trigger is pulled. Speed is low when the switch
trigger is pulled slightly and increases as the switch
trigger is pulled more.
䡬
When releasing the switch trigger, the brake will
be applied for immediate stopping.
2. Ro Hammering
Align the “
” mark with the “
” mark by
rotating the change lever to set the “Ro
Hammering” function. (
Fig. 8
)
(1) Mount the drill bit.
(2) Pull the trigger switch after applying the drill bit
tip to the drilling position. (
Fig. 10
)
(3) Pushing the rotary hammer forcibly is not necessary
at all. Pushing slightly so that drill dust comes out
gradually is just sufficient.
CAUTION:
When the drill bit touches construction iron bar, the
bit will stop immediately and the rotary hammer
will react to revolve. Therefore please grip the side
handle and handle tightly as shown in
Fig. 10
.
3. Rotation only
Align the “
” mark with the “
” mark by rotating
the change lever to set the “Rotation only” function.
(
Fig. 8
)
To drill a wood or metal material using the optional
drill chuck and chuck adapter, proceed as follows.
Installing drill chuck and chuck adapter: (
Fig. 11
)
(1) Attach the drill chuck to the chuck adaptor.
(2) The part of the SDS-plus shank is the same as the
drill bit. Therefore, refer to the item of “Mounting
the drill bit” for attaching it.
(1) Clean the shank portion of the drill bit.
(2) Insert the drill bit in a twisting manner into the tool
holder until it latches itself. (
Fig. 4
)
(3) Check the latching by pulling on the drill bit.
(4) To remove the drill bit, fully pull the grip in the
direction of the arrow and pull out the drill bit.
2. Confirm that the battery is mounted correctly.
3. Installation of dust cup or dust collector (B) (Optional
accessories) (Fig. 6, Fig. 7)
When using a rotary hammer for upward drilling
operations attach a dust cup or a dust collector (B)
to collect dust or particles for easy operation.
䡬
Installing the dust cup
Use the dust cup by attaching to the drill bit as
shown in
Fig. 6
.
When using a bit which has big diameter, enlarge
the center hole of the dust cup with this rotary
hammer.
䡬
Installing dust collector (B)
When using dust collector (B), insert dust collector
(B) from the tip of the bit by aligning it to the
groove on the grip. (
Fig. 7
)
CAUTION:
䡬
The dust cup and dust collector (B) are for exclusive
use of concrete drilling work. Do not use them for
wood or metal drilling work.
䡬
Insert dust collector (B) completely into the chuck
part of the main unit.
䡬
When turning the rotary hammer on while dust
collector (B) is detached from a concrete surface,
dust collector (B) will rotate together with the drill
bit. Make sure to turn on the switch after pressing
dust cup on the concrete surface. When using dust
collector (B) attached to a drill bit that has more
than 190 mm of overall length, dust collector (B)
cannot touch the concrete surface and will rotate.
Therefore, please use dust collector (B) by attaching
to drill bits which have 166 mm, 160 mm, and 110
mm overall length.
䡬
Dump particles after every two or three holes when
drilling.
䡬
Please replace the drill bit after removing dust
collector (B).
4. Selecting the driver bit
Screw heads or bits will be damaged unless a bit
appropriate for the screw diameter is employed to
drive in the screws.
5. Confirm the direction of bit rotation (Fig. 9)
The bit rotates clockwise (viewed from the rear
side) by pushing the R-side of the push button. (
Fig.
9-a
)
The L-side of the push button is pushed to turn the
bit counterclockwise. (
Fig. 9-b
)
The motor does not rotate if the push button is set
to the center position. (
Fig. 9-c
)
6. Continuous drilling
The number of holes that can be drilled in concrete
after one recharge is shown in
Table 4
.
Possible continuous
Bit dia.
Depth
drilling number (holes)
(mm)
(mm)
EB2420
EB2430HA EB2433X
6.5
75
115
125
8.5
45
70
75
12.5
40
55
60
14.5
60
30
45
50
18
15
25
28
24
5
7
8
01Eng_DH24DVA_WE
11/27/08, 13:36
13
