--- 13 ---
1 Remove the three couplers of the Wire Harness
[162]
(white/blue, yellow/brown,
and black/black) that connects the Stator
[12]
with the Panel
Ass’y
[151]
and
remove the Screw (W/W
asher) M5 x 12
[13]
.
2 Remove the Hex. Bolt M6 x 24
[77]
from the side of the Panel
Ass’y
[151]
.
3 Pull the Panel
Ass’y
[151]
and remove the couplers of the Wire Harness
[94]
and
the Wire Harness
[161]
from the Engine
[71]
behind the Box
Ass’y
[141]
.
4 Push the Wire Harness
[162]
in the Box
Ass’y
[141]
.
5 Remove the Hex. Bolt M6 x 12
[147]
and open the Box
Ass’y
[141]
a little.
6 Push the claws of the couplers (above step 3 ) fitted in the Box
Ass’y
[141]
to
remove it from the Box
Ass’y
[141]
.
7 Open the Box
Ass’y
[141]
and remove the Condenser
[145]
from the Wire
Harness
[162]
.
8 Replace the Condenser
[145]
fitted in the Box
Ass’y
[141]
.
Cause
Corrective action
Procedure
(i) The
Condenser
[145]
is damaged
or deteriorated.
Replace the Condenser
[145]
.
(ii)
The main coil or the sub coil is
broken or short-circuited.
Replace the Stator
[12]
.
1 Remove the three couplers of the Wire Harness
[162]
(white/blue, yellow/brown,
and black/black) that connects the Stator
[12]
with the Panel
Ass’y
[151]
and
remove the Screw (W/W
asher) M5 x 12
[13]
.
2 Remove the Hex. Bolt M8 x 14
[9]
.
3 Remove the
Through Bolt M6 x 120
[10]
(Model E 43), M6 x 155
[10]
(Model E 60) or M6 x 155
[10]
(Model E 71).
4 Remove the Hex. Bolt M10 x 30
[75]
.
5 Remove the Rear Cover
[1
1]
.
6 Replace the Stator
[12]
.
(iii)
The field coil is broken.
Replace the Rotor Comp.
[3]
.
1 Remove the three couplers of the Wire Harness
[162]
(white/blue, yellow/brown,
and black/black) that connects the Stator
[12]
with the Panel
Ass’y
[151]
and
remove the Screw (W/W
asher) M5 x 12
[13]
.
2 Remove the Hex. Bolt M8 x 14
[9]
.
3 Remove the
Through Bolt M6 x 120
[10]
(Model E 43), M6 x 155
[10]
(Model E 60) or M6 x 155
[10]
(Model E 71).
4 Remove the Hex. Bolt M10 x 30
[75]
.
5 Remove the Rear Cover
[1
1]
.
6 Replace the Stator
[12]
.
7 Remove the Bolt M10 x 215
[2]
(Model E 43), M10 x 215
[2]
(Model E 60) or
M10 x 260
[2]
(Model E 71) without removing the Rotor Comp.
[3]
from the Engine
[71]
.
8
T
ighten the rotor puller bolt (jig) as a substitute for the Bolt M10
[2]
.
Summary of Contents for E 71
Page 44: ......
