!,#
#
#
On-screen Information
(The following messages will appear on screen, depending on the status of projector.)
Message
Contents
Remedy
LAMP1 TIME EEEEh.
LAMP2 TIME EEEEh.
Appears when the lamp-accumulated time exceeds 6000
hours.
*1
LAMP1 TIME EEEEh.
LAMP2 TIME FAILURE.
PLEASE REPLACE
LAMP2
When other lamp is off, message is displayed in approx. 20.
*
This case is when
(
LAMP2
)
is off.
+
LAMP TIME EEEEh.
LAMP CHAN1E AFTER
EEh
Appears
lamp operation hours as total from 100 hours
of “forced lights out time function” before.
&-
(
**h
)
displays time to replace the lamp.
LAMP TIME EEEEh.
LAMP CHAN1E IN A
MINUTE.
Appears
message when exceed “forced lights out time
function” lamp operation hours as total. Lamp is off
after
15 seconds forcibly and lamp is replaced the lamp
automatically.
When other lamp is trouble,
lamp is off after
15 seconds
forcibly.
CONTINUOUS
LAMP1 TIME EEh
LAMP2 TIME
--
h
Appear when other lamp is trouble
or continuous
operation hours
exceed 25 hours.
*
This case is when “LAMP1” is on.
+
Ask the dealer to replace
the lamp.
ABNORMAL
TEMPERATURE
The temperature is extremely high.
&.
Ask the dealer for
inspection.
FAN FAILURE
F2
Fan is faulty.
&/
*
The case is that fan of
(
F2
)
is trouble..
+
Ask the dealer to replace
the fan.
8
0
12
Appear the time after power on in auto lamp change
function.
Not appear the time when this function is invalid.
*
This case is when the time is 8:12.
+
Set the present time.
1
(See p.19-TIME SETTING)
&-
The message will disappear in 20 seconds, but reappear whenever power is turned on again.
&2
#
When set the function of forced lamp out .
#
&.
The message will disappear in approx. 1 seconds, and power will also go off.
&/
The message will disappear in approx. 1 minute, and power will also go off.
#
Indicators (LED lamps)
#
No
Name
Operation
Remarks
1
Power indicator
(ON/STAND BY)
(Terminal plate)
'
Lights orange in the standby status (main power on).
'
Blinks green during warm-up (power on by power switch or remote control).
'
Lights green during operation.
'
Blinks orange during cooling down (power off by power switch or remote
control).
'
Lights red when the projector is faulty or the lamp does not light.
2-color LED
used
Indicate the circuit that is faulty, or stops and gives its status.
If the following indicators light or blink simultaneously when the
ON/STANDBY indicator lights red,
'
LAMP: Lights when the lamp is faulty; blinks when there is no lamp.
'
TEMP: Lights when the temperature is abnormal; blinks when the
fan operation is faulty.
&-
Indicate the fan is faulty, indicator lights blink.
&2
'
TEMP, ST1
0
Lights when main circuit board is abnormal voltage.
2
Fault judgment
indicators
(LAMP, TEMP)
(Terminal plate)
ON/STANDBY indicator lights green and lamp lights,
'
Other lamp is trouble when lamp changer is mounted.
A fault could
have occurred
or it is
necessary to
replace lamp
3
Consult your
dealer.
'
CPU: Lights red or blinks during faulty run of program.
'
ST2: Lights red when lamp changer communication is faulty.
A fault could
have occurred:
Consult your
dealer.
3
Status
indicators
on
main circuit board
(Terminal plate)
'
TERM: Lights green when RS485 termination is set.
&-
Since power will turn off in approx. 1 seconds, the lamp indicator will also turn off.
&2
#
The message will disappear in approx. 1 seconds, and power will also go off
List of OSD Messages
!