background image

 

IMPORTANT INFORMATION 

READ FIRST 

• READ this user's manual before using this user system interface cable. 

• KEEP the user's manual handy for future reference. 

Do not attempt to use the user system interface cable until you fully understand its 
mechanism. 

User System Interface Cable: 

     Throughout this document, the term "user system interface cable" shall be defined as the 
following product produced only by Hitachi, Ltd. excluding all subsidiary products. 

• 

User system interface cable (HS2212ECH61H) 

     The user system or a host computer is not included in this definition. 

Purpose of the User System Interface Cable:  

     This user system interface cable is for connecting the emulator station and user system.  This 
user system interface cable must only be used for the above purpose. 

Improvement Policy:  

     Hitachi, Ltd. (including its subsidiaries, hereafter collectively referred to as Hitachi) pursues a 
policy of continuing improvement in design, performance, functions, and safety of the user system 
interface cable.  Hitachi reserves the right to change, wholly or partially, the specifications, design, 
user's manual, and other documentation at any time without notice. 

Target User of the User System Interface Cable:  

     This user system interface cable should only be used by those who have carefully read and 
thoroughly understood the information and restrictions contained in the user's manual. Do not 
attempt to use the user system interface cable until you fully understand its mechanism. 

     It is highly recommended that first-time users be instructed by users that are well versed in the 
operation of the user system interface cable. 

Summary of Contents for FP-64E



























Reviews: