background image

Section 2   Connection Procedures 

2.1 

Connecting User System Interface Cable to Emulator Station 

WARNING

 

   

Observe the precautions listed below.  Failure to do so  

  will result in a FIRE HAZARD and will damage the user  
  system and the emulator product or will result in  
  PERSONAL INJURY.  The USER PROGRAM will be  
  LOST.   
  1.   Always switch OFF the user system and the emulator 
   

product before the USER SYSTEM INTERFACE CABLE  

   

is connected to or removed from any part.  Before  

   

connecting, make sure that pin 1 on both sides are  

   

correctly aligned.  

  2.  The user system interface cable dedicated to the  
   

emulator must be used.   

To connect the cable body to the emulator station, follow the instructions below. 

1.  Make sure the user system and emulator station are turned off. 

CAUTION 

   

When connecting or removing the user system interface 

  cable, apply force only in the direction suitable for 
  connection or removal, while making sure not to bend or 
  twist the cable or connectors. Otherwise, the connectors will 
 be damaged. 

2. 

After making sure the direction of the cable body connector is correct, firmly insert the cable 
body connector into the emulator station socket (figure 2). 

3. 

If the emulator has holes for fastening screws, fasten the cable body to the emulator station by 
using the attached screws for fixing the cable body. 

 

Summary of Contents for FP-64E



























Reviews: