MAX
MEMO
1)
®–µ‘¥µ—È߇§√◊ËÕß∑’ˉÀπ
Where to install
❑
®–µâÕßµ‘¥µ—È߇§√◊ËÕ߇¢â“°—∫ºπ—ßµ“¡√Ÿª
❑
§«√µ‘¥µ—È߇§√◊ËÕß Ÿß°«à“√–¥—∫Õ¬à“ßπâÕ¬
1.70
‡¡µ√
❑
Must be installed at the wall, as the picture.
❑
It should be installed above the floor at least 1.70 M.
2)
°“√‡ªî¥Ω“§√Õ∫‡§√◊ËÕßÕÕ°®“°∞“π‡§√◊ËÕß
Opening of the cover out of the unit base.
❑
∂Õ¥ °√Ÿ à«π≈à“ߢÕßµ—«‡§√◊ËÕßÕÕ°
❑
¥÷ßΩ“§√Õ∫¥â“π∫πÕÕ°
❑
Remove the screw at the bottom of the unit.
❑
Pull off upper cover.
3)
µ‘¥µ—Èßµ—«‡§√◊ËÕß∫πºπ—ߧÕπ°√’µ Õ‘∞ À√◊Õºπ—ß°√–‡∫◊ÈÕߥ‘π‡º“
Install on concrete, brick or ceramic wall
❑
„™â «à“π‡®“–√Ÿ∫πºπ—ß
❑
Õ¥ª≈—Í°‡¢â“‰ª„π√Ÿ
❑
¢—π °√Ÿ·µà≈–µ—«‡¢â“‰ª„πª≈—Í°µÕπ∫π Õßµ—« ‚¥¬§â“ß„Àâ‡À≈◊Õ§«“¡¬“«
°√Ÿ‡Õ“‰«â
3
∂÷ß
4
¡‘≈≈‘‡¡µ√ µàÕ‰ª·¢«π™ÿ¥‡§√◊ËÕß∫π °√Ÿ ·≈⫧àÕ¬¢—π
°√Ÿ¬÷¥∑—Èß
4
µ—« „Àâ¬÷¥·πàπ·≈–Õÿ¥√Ÿ¬÷¥ °√Ÿ¥â«¬´‘≈‘‚§π
(Silicone)
❑
°“√µ‘¥µ—Èß∑’Ë·¢«πÀ—«Ωí°∫—«µ‘¥µ—Èß∑’Ë·¢«πÀ—«Ωí°∫—« „ÀâÕ¬Ÿà„π√–¥—∫∑’Ë ‡¡◊ËÕ
·¢«πÀ—«Ωí°∫—«·≈â« à«π Ÿß ÿ¥¢ÕßÀ—«Ωí°∫—«µâÕ߉¡à Ÿß°«à“ à«π∫π ÿ¥¢Õß
µ—«‡§√◊ËÕß
❑
À≈—ß®“°µ‘¥µ—È߇§√◊ËÕ߇ √Á®‡√’¬∫√âÕ¬ µâÕßµ‘¥µ—Èß™ÿ¥Õÿª°√≥åªÑÕß°—π·√ߥ—π
πÈ”‡°‘π‡¢â“°—∫µ—«‡§√◊ËÕß∑“ߥâ“π∑“ßπÈ”‡¢â“∑ÿ°§√—Èß
❑
Drill holes on the wall.
❑
Insert the plug to the holes.
❑
Tighten two screws in the top plug leaving about 3 to 4 mm.
space. Next hang the heater unit on the screws and move to
tighten the 4 screws and seal the holes with silicone.
❑
Installation the hanger on level properly. If shower head is
hung the highest shower head not over the top of water
heater.
❑
After installation of the heater unit, proceed to install the safety
valve to the until at the water inlet tube.
2.
°“√µ‘¥µ—Èß
INSTALLATION
‡°‘π
1.7
‡¡µ√
More than 1.7 M
°√Ÿ¬÷¥¥â“π≈à“ß
Screw for fastening
™ÿ¥Õÿª°√≥å
ªÑÕß°—π
·√ߥ—ππÈ”‡°‘π
Safety valve
25
¡¡.
25
MM.
6
¡¡.
6
MM.
&
MAX
MEMO