Hitachi L200-002NFE2 Instruction Manual Download | Manualshive

Page: 148 / 304

background image

Connecting to PLCs and Other Devices

Oper

ations

and Monitor

ing

4–4

Connecting to PLCs and Other Devices

Hitachi inverters (drives) are useful in many types of applications. During installation,
the inverter keypad (or other programming device) will facilitate the initial configura-
tion. After installation, the inverter will generally receive its control commands through
the control logic connector or serial interface from another controlling device. In a
simple application such as single-conveyor speed control, a Run/Stop switch and poten-
tiometer will give the operator all the required control. In a sophisticated application,
you may have a

programmable logic controller

(PLC) as the system controller, with

several connections to the inverter.

It is not possible to cover all the possible types of application in this manual. It will be
necessary for you to know the electrical characteristics of the devices you want to
connect to the inverter. Then, this section and the following sections on I/O terminal
functions can help you quickly and safely connect those devices to the inverter.

CAUTION:

It is possible to damage the inverter or other devices if your application

exceeds the maximum current or voltage characteristics of a connection point.

The connections between the inverter and
other devices rely on the electrical input/
output characteristics at both ends of each
connection, shown in the diagram to the
right. The inverter’s configurable inputs
accept either a sourcing or sinking output
from an external device (such as a PLC).
This chapter shows the inverter’s internal
electrical component(s) at each I/O termi-
nal. In some cases, you will need to insert
a power source in the interface wiring.

In order to avoid equipment damage and
get your application running smoothly, we
recommend drawing a schematic of each
connection between the inverter and the
other device. Include the internal compo-
nents of each device in the schematic, so
that it makes a complete circuit loop.

After making the schematic, then:

1.

Verify that the current and voltage for
each connection is within the operating
limits of each device.

2.

Make sure that the logic sense (active high or active low) of any ON/OFF connection
is correct.

3.

Check the zero and span (curve end points) for analog connections, and be sure the
scale factor from input to output is correct.

4.

Understand what will happen at the system level if any particular device suddenly
loses power, or powers up after other devices.

Other device

Input

circuit

Output

circuit

Inverter

Input

circuit

Output

circuit

PCS

1

2

3

4

5

L

Input

circuits

+ –

signal

signal

return

return

PLC

Inverter

24V

GND

+Com

«
...
146
147
148
149
150
...
»

Summary of Contents for L200-002NFE2

















































































































































































































































































































Reviews:

No comments

Related manuals for L200-002NFE2

CSI-75K-T40001-E

Brand: CanadianSolar Pages: 45

DuoPak APD 2067

Brand: Absolute Process Instruments Pages: 2

EAL580 MT Series

Brand: Baumer Pages: 74

UNIRAC POLETOPS 5000 Series

Brand: Hilti Pages: 4

AIS Splitter 100

Brand: Raymarine Pages: 24

Brand: ADF Web Pages: 30

Brand: Walter Pages: 216

Brand: GE Pages: 55

COMBIVERT F5 Series

Brand: KEB Pages: 116

TopTronic E Solar TTE-SOL

Brand: Hoval Pages: 95

Rossini Transport

Brand: DCS Pages: 31

Giga-McBasic-II

Brand: B&B Electronics Pages: 14

Brand: VigilLink Pages: 6

DASNET-SPLITTER

Brand: D.A.S. Pages: 12

Brand: Digitus Pages: 6

Brand: SIIG Pages: 12

Brand: Duracraft Pages: 62

Brand: J-Tech Digital Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands