Hitachi L200-002NFE2 Instruction Manual Download | Manualshive

Page: 150 / 304

background image

Control Logic Signal Specifications

Oper

ations

and Monitor

ing

4–6

Control Logic Signal Specifications

Specifications for the logic connection terminals are in the following table:

Note 1:

The two terminals [L] are electrically connected together inside the inverter.

Note 2:

We recommend using [L] logic GND (to the right) for logic input circuits and
[L] analog GND (to the left) for analog I/O circuits.

Note 3:

Default relay N.O./N.C. configuration is reversed. See page

Relay contacts

Logic inputs

Analog

inputs

Analog

output

Logic

outputs

12 11

1

2

3

4

5

L

L

H O OI

AM

CM2

PCS

AL2

AL0

AL1

The control logic connectors are located just
behind the front housing cover. The relay contacts
are just to the left of the logic connectors.
Connector labeling is shown below.

Terminal Name

Description

Ratings

[PCS]

+24V for logic inputs

24VDC, 100 mA max. (do not short to terminal L)

[1], [2], [3], [4], [5]

Discrete logic inputs

27VDC max. (use PCS or an external supply refer-
enced to terminal L)

[L] (right) *1

GND for logic inputs

sum of input [1]—[5] currents (return)

[11], [12]

Discrete logic outputs

50mA maximum ON state current,
27 VDC maximum OFF state voltage

[CM2]

GND for logic outputs

100 mA: sum of 11 and 12 currents (return)

[AM]

Analog voltage output

0 to 10VDC, 1mA maximum

[L] (left) *2

GND for analog signals

sum of OI, O, H, and AM currents (return)

[OI]

Analog input, current

4 to 19.6 mA range, 20 mA nominal,
input impedance 250

Ω

[O]

Analog input, voltage

0 to 9.8 VDC range, 10VDC nominal,
input impedance 10 k

Ω

[H]

+10V analog reference

10VDC nominal, 10 mA max

[AL0]

Relay common contact

250 VAC, 2.5A (R load) max.,
250 VAC, 0.2A (I load, P.F.=0.4) max.
100 VAC, 10mA min.
30 VDC, 3.0A (R load) max.
30 VDC, 0.7A (I load, P.F.=0.4) max.
5 VDC, 100mA min.

[AL1] *3

Relay contact, normally open

[AL2] *3

Relay contact, normally
closed

«
...
148
149
150
151
152
...
»

Summary of Contents for L200-002NFE2

















































































































































































































































































































Reviews:

No comments

Related manuals for L200-002NFE2

Brand: ABB Pages: 62

Brand: Parker Pages: 99

Brand: Magnimage Pages: 40

Brand: Icy Box Pages: 2

HUBNER BERLIN POG 10 + DSL

Brand: Baumer Pages: 36

Brand: NEXENTRO Pages: 8

Brand: Enerdrive Pages: 2

Brand: Caen Pages: 17

Brand: Humandata Pages: 10

SITE INVERTER 300

Brand: ICT Pages: 8

B+B SmartWorx 485USB9F-2W

Brand: Advantech Pages: 2

Brand: DeLOCK Pages: 2

Brand: Planet Pages: 20

Brand: Lindy Pages: 14

Brand: leadsun Pages: 8

Multi-Decoder MD-2

Brand: tams elektronik Pages: 40

Brand: Yangzhou Shenzhou Wind-driven Generator Pages: 35

Brand: NSK Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands