Hitachi L200-002NFE2 Instruction Manual Download | Manualshive

Page: 217 / 304

background image

L200

2

Inverter

T

roub

leshooting

and Maintenance

6–5

Monitoring Trip Events, History, & Conditions

Fault Detection and Clearing

The microprocessor in the inverter detects a variety
of fault conditions and captures the event, record-
ing it in a history table. The inverter output turns
OFF, or “trips” similar to the way a circuit breaker
trips due to an over-current condition. Most faults
occur when the motor is running (refer to the
diagram to the right). However, the inverter could
have an internal fault and trip in Stop Mode. In
either case, you can clear the fault by pressing the Stop/Reset key. Additionally, you can
clear the inverter’s cumulative trip history by performing the procedure

Factory Default Settings” on page 6–8

(setting B084=00 will clear the trip history but

leave inverter settings intact).

Error Codes

An error code will appear on the display automatically when a fault causes the inverter to
trip. The following table lists the cause associated with the error.

Run

Stop

Trip

Fault

Fault

STOP

RESET

STOP

RESET

RUN

Error

Code

Name

Cause(s)

E 0 1

Over-current event while
at constant speed

The inverter output was short-circuited, or the motor
shaft is locked or has a heavy load. These conditions
cause excessive current for the inverter, so the inverter
output is turned OFF.

The dual-voltage motor is wired incorrectly.

E 0 2

Over-current event during
deceleration

E 0 3

Over-current event during
acceleration

E 0 4

Over-current event during
other conditions

E 0 5

Overload protection

When a motor overload is detected by the electronic
thermal function, the inverter trips and turns OFF its
output.

E 0 7

Over-voltage protection

When the DC bus voltage exceeds a threshold, due to
regenerative energy from the motor.

E 0 8

EEPROM error

When the built-in EEPROM memory has problems
due to noise or excessive temperature, the inverter
trips and turns OFF its output to the motor.

E 0 9

Under-voltage error

A decrease of internal DC bus voltage below a thresh-
old results in a control circuit fault. This condition can
also generate excessive motor heat or cause low
torque. The inverter trips and turns OFF its output.

E 1 1
E 2 2

CPU error

A malfunction in the built-in CPU has occurred, so
the inverter trips and turns OFF its output to the
motor.

«
...
215
216
217
218
219
...
»

Summary of Contents for L200-002NFE2

















































































































































































































































































































Reviews:

No comments

Related manuals for L200-002NFE2

Brand: Alca Power Pages: 8

Brand: Baumer Pages: 36

Brand: DeLOCK Pages: 16

Brand: AVT Pages: 82

Brand: B&B Electronics Pages: 2

Brand: Cypress Pages: 12

Brand: Lindy Pages: 14

BRAVO ST 230 VAC

Brand: Helios Power Solutions Pages: 39

Brand: TDK-Lambda Pages: 36

Brand: APT Pages: 43

Brand: Orgautomatech Pages: 8

EXT-DVIDL-2-HDMIR

Brand: Gefen Pages: 14

MobilePower PRO

Brand: Heyner Pages: 4

Brand: Urrea Pages: 12

225 Watt Power Inverter

Brand: Vector Pages: 6

Brand: ClickTronic Pages: 42

Brand: TR-Electronic Pages: 91

Brand: Micno Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands