Hitachi L200-002NFE2 Instruction Manual Download | Manualshive

Page: 294 / 304

background image

CE–EMC Installation Guidelines

Appendix D

D–2

CE–EMC Installation Guidelines

You are required to satisfy the EMC directive (89/336/EEC) when using an L200

2

inverter in an EU country. To satisfy the EMC directive and to comply with standard,
follow the guidelines in this section.

1.

As user you must ensure that the HF (high frequency) impedance between adjustable
frequency inverter, filter, and ground is as small as possible.

• Ensure that the connections are metallic and have the largest possible contact

areas (zinc-plated mounting plates).

2.

Avoid conductor loops that act like antennas, especially loops that encompass large
areas.

• Avoid unnecessary conductor loops.

• Avoid parallel arrangement of low-level signal wiring and power-carrying or

noise-prone conductors.

3.

Use shielded wiring for the motor cable and all analog and digital control lines.

• Allow the effective shield area of these lines to remain as large as possible; i.e., do

not strip away the shield (screen) further away from the cable end than absolutely
necessary.

• With integrated systems (for example, when the adjustable frequency inverter is

communicating with some type of supervisory controller or host computer in the
same control cabinet and they are connected at the same PE-potential),
connect the shields of the control lines to PE (protective earth) at both
ends. With distributed systems (for example the communicating supervisory
controller or host computer is not in the same control cabinet and there is a
distance between the systems), we recommend connecting the shield of the
control lines only at the end connecting to the adjustable frequency inverter. If
possible, route the other end of the control lines directly to the cable entry section
of the supervisory controller or host computer. The shield conductor of the motor
cables always must connected to PE at both ends.

• To achieve a large area contact between shield and PE-potential, use a

PG screw with a metallic shell, or use a metallic mounting clip.

• Use only cable with braided, tinned copper mesh shield (type “CY”) with 85%

coverage.

• The shielding continuity should not be broken at any point in the cable. If the use

of reactors, contactors, terminals, or safety switches in the motor output is neces-
sary, the unshielded section should be kept as short as possible.

• Some motors have a rubber gasket between terminal box and motor housing. Very

often, the terminal boxes, and particularly the threads for the metal PG screw
connections, are painted. Make sure there is always a good metallic connection
between the shielding of the motor cable, the metal PG screw connection, the
terminal box, and the motor housing. If necessary, carefully remove paint between
conducting surfaces.

«
...
292
293
294
295
296
...
»

Summary of Contents for L200-002NFE2

















































































































































































































































































































Reviews:

No comments

Related manuals for L200-002NFE2

Brand: 3onedata Pages: 3

Brand: QFX Pages: 44

Brand: hc-cargo Pages: 38

Brand: Sungrow Pages: 136

Brand: My Cable Mart Pages: 4

Brand: Rohde & Schwarz Pages: 17

Brand: REI Pages: 4

Brand: ICP DAS USA Pages: 148

Brand: East Pages: 66

EVERVOLT EVHB-I7

Brand: Panasonic Pages: 43

Brand: ACT Pages: 2

Brand: ACT Pages: 166

Brand: Charmeg Pages: 17

Brand: Violectric Pages: 28

Brand: Motorola Pages: 41

Brand: Motorola Pages: 2

Brand: Motorola Pages: 336

Brand: Motorola Pages: 424

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands