Chapter 4
・
4.1.4.1
・
※
4.1.4.2
・
※
4.1.4.3
※
Chapter 4
4.1.4 Doing a test
・
This explains the method to how to do a test run using
the keypad.
Menu
Output frequency
Output current
Input terminal monitor
RUN
FW
4.1.4.1
Confirm the operation command.
・
In the position
displayed FW
enabled.
⇒
Go to
※
In the cases that is not displayed, and want
from the keypad
reference to FW
RUN command selection.
⇒
Go to
[4.
4.1.4.2
Frequency reference
・
In the upper illustration, in the position (F), when values
other than 0.00
is already set.
※
In the case that
change the
case that you want to change to an
such, the frequency command selection must be
changed.
⇒
Go to
4.1.4.3
Start the
key and the motor will accelerate.
※
When the motor does not rotate, please refer to the
troubleshooting.
Chapter 4
oing a test run…
This explains the method to how to do a test run using
.
Home screen
Output frequency
Output current
Input terminal monitor
oFW
RUN
FW
(E)↑ (F)↑
Confirm the operation command.
n the position (E) of the upper illustration
displayed FW or RV, the RUN key of the
Go to
[4.1.4.2]
cases that is not displayed, and want
keypad, or want to change the RUN command
to FW terminal
RUN command selection.
4.1.4.4 Run Command reference change
requency reference
In the upper illustration, in the position (F), when values
other than 0.00 are displayed
is already set.
⇒
Go to
[4.1.4.
In the case that 0.00 is displayed, is necessary to
change the value of the frequency reference. In the
you want to change to an
requency command selection must be
Go to
[4.1.4.5]
Start the output
and the motor will accelerate.
When the motor does not rotate, please refer to the
troubleshooting.
run…
This explains the method to how to do a test run using
Home screen
46.49
Output frequency
46.49 Hz
Input terminal monitor
LLLLLLLLLLL
M1
(E)↑ (F)↑
Confirm the operation command.
of the upper illustration
the RUN key of the
cases that is not displayed, and want
, or want to change the RUN command
terminal, is necessary to change the
RUN command selection.
1.4.4 Run Command reference change
requency reference status checking
In the upper illustration, in the position (F), when values
are displayed, the frequency reference
4.1.4.3]
is displayed, is necessary to
frequency reference. In the
you want to change to an analog
requency command selection must be
output by pressing the RUN
and the motor will accelerate.
When the motor does not rotate, please refer to the
This explains the method to how to do a test run using
Option
46.49 Hz
11.9 A
LLLLLLLLLLL
H01
Confirm the operation command.
of the upper illustration, when is
the RUN key of the keypad is
cases that is not displayed, and want to operate
, or want to change the RUN command
, is necessary to change the
1.4.4 Run Command reference change
status checking
In the upper illustration, in the position (F), when values
, the frequency reference
is displayed, is necessary to
frequency reference. In the
analog input and
requency command selection must be
by pressing the RUN
and the motor will accelerate.
When the motor does not rotate, please refer to the
4-5
This explains the method to how to do a test run using
, when is
to operate
, or want to change the RUN command
, is necessary to change the
1.4.4 Run Command reference change]
status checking.
In the upper illustration, in the position (F), when values
, the frequency reference
frequency reference. In the
input and
by pressing the RUN
When the motor does not rotate, please refer to the
4.1.4.4
①
parameter setting screen and by pressing the SEL(O)
key, the parameter section of the parameter setting
screen will blink.
②
(
③
keys select the RUN operation to be executed
all the choices
one
④
in the position (E) FW or RV
the
⇒
Go to
For parameter configuration
1.4.4
RUN command
Press the RIGHT
parameter setting screen and by pressing the SEL(O)
key, the parameter section of the parameter setting
screen will blink.
Back
Output frequency
STOP
F
A-01
Set Speed
Change the code
) keys to
Back
Output frequency
STOP
AA11
1
RUN command selection_M1
01:[FW]/[RV] terminal
Press the SEL
keys select the RUN operation to be executed
all the choices. In this case
one selected.
Back
AA111
RUN command selection_M1
STOP
00:[FW]/[RV] terminal
01:3-wire
02:Keypad
03:RS485
To save the
in the position (E) FW or RV
the F1 key, and will
Go to
[4.1.4.2
For parameter configuration
RUN command
RIGHT( ) key, after moving to the
parameter setting screen and by pressing the SEL(O)
key, the parameter section of the parameter setting
screen will blink.
Output frequency
oFW
Set Speed-M (Keypad
the code with UP/DOWN/LEFT/RIGHT
keys to [AA111].
Output frequency
oFW
RUN command selection_M1
01:[FW]/[RV] terminal
SEL(O) key and then
keys select the RUN operation to be executed
. In this case [
RUN command selection_M1
oFW
:[FW]/[RV] terminal
wire
Keypad’s RUN key
:RS485
To save the changes press
in the position (E) FW or RV
, and will go to Home screen.
2]
For parameter configuration
RUN command reference change
key, after moving to the
parameter setting screen and by pressing the SEL(O)
key, the parameter section of the parameter setting
Option
29.51
0.00 Hz
M1
M (Keypad)
29.51 Hz
with UP/DOWN/LEFT/RIGHT
Option
29.51
0.00 Hz
M1
RUN command selection_M1
01:[FW]/[RV] terminal
and then with UP/DOWN
keys select the RUN operation to be executed
[03:Keypad’s RUN key]
Option
29.51
RUN command selection_M1
M1
changes press the SEL (O)
in the position (E) FW or RV should be displayed. Press
to Home screen.
For parameter configuration
change
key, after moving to the
parameter setting screen and by pressing the SEL(O)
key, the parameter section of the parameter setting
Option
0.00 Hz
H03
29.51 Hz
with UP/DOWN/LEFT/RIGHT
Option
0.00 Hz
H03
[1-8]
with UP/DOWN(
keys select the RUN operation to be executed between
’s RUN key] is the
Option
H03
key and then
displayed. Press
)
between
the
and then
displayed. Press
Summary of Contents for P1-00041HFEF
Page 6: ...0 5 Contents Contents Memo ...
Page 42: ...2 26 Chapter 2 Installation and Wiring Memo ...
Page 129: ...Index Index 3 memo ...
Page 130: ...Index Index 4 memo ...
