Re-indication method for defective mode .
1.
2.
3.
4.
5.
6.
Turn the circuit breaker OFF and set the remote controller
STOP position.
Turn the circuit breaker ON.
Set the remote control to “Cooling” and the set temperature to “32”.
Set the blower speed according to the indicated failure condition. (Refer
to the corresponding table.)
Press the
［
∧
］
button while pressing the temperature setting button
［
］
.
(Transmission is performed.)
The main unit makes the receiving sound
［
Pi-
］
and becomes the
defective indication mode.(Timer lamp goes on and off, but if the
unit has no memory, the indication is not shown.)
Clear method for data of defective mode.
1.
2.
3.
4.
5.
6.
Proceed the re-indication of defective mode. (proceed without fail, after having the
re-indication, do not operate the remote controller except for indicated ones.)
Turn the circuit breaker OFF. (Continue OFF more than 5 seconds.)
Turn the circuit breaker ON.
Set the remote controller HEAT and to be set 16
℃
and press the
［ ］
button.
while pressing the
［∨］
of temperature buttons. Transmission.
Finish the clear after having the receiving sound
［
Pii-
］
of one second.
Turn the circuit breaker OFF and finish.( Please turn OFF once without fail.)
Notes
This function is valid only once right after switching ON the power and does not work if other remote controller operation
was made prior to it.
Take note that this function may not work when not following the above procedures.
(If it does not work, switch OFF the power and try again.)
If nothing is stored in the memory, the lamp does not blink even if re-indication operation is carried out.
After carrying out re-indication operation, the remote controller operation will not be accepted once the data has been
cleared. To carry out normal operation, switch OFF the power beforehand.
Self Diagnosis Memory Function
Defective modes stored in the non-volatile memory of the indoor unit are re-indicated by the remote controller operation. This
is useful to check the defective mode when switching OFF the power or restarting the unit operation without checking the
number of blinking of the defective indication lamp. (The defective mode which occurred the last is memorized.)
Defective modes of which occurrence frequency is too low to indicate on the indoor unit are also stored in the memory, thus
defective phenomenon which was not checked at the visit can be found by clearing the memory and rechecking the memory
contents later on.
Finish after turning the circuit breaker OFF.(Please turn OFF once without fail.)
7.
Error codes can also be displayed with the remote controller.
For details regarding the contents of error codes displayed with the remote controller,
refer to “Displaying Error Codes with the Remote Controller.”
Blower speed
Data
Failure data blower speed setting
Auto
Newest
2nd newest
3rd newest
4th newest
Oldest
Strong
Weak
Very low
Quiet
83
Summary of Contents for RAC-25FPA
