English
8
c) When battery pack is not in use, keep it away
from other metal objects like paper clips, coins,
keys, nails, screws, or other small metal objects
that can make a connection from one terminal
to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause
irritation or burns.
6) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool
is maintained.
PRECAUTION
Keep children and infirm persons away.
When not in use, tools should be stored out of reach of
children and infirm persons.
PRECAUTIONS FOR ELECTRONIC PULSE DRIVER
1.
Hold power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring.
Fasteners contacting
a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator
an electric shock.
2.
This is a portable tool for drilling, tightening and
loosenig screws. Use it only for these operations.
3.
Use the earplugs if using for a long time.
4.
One-hand operation is extremely dangerous; hold
the unit firmly with both hands when operating.
5.
After installing the driver bit, pull lightly out the
bit to make sure that it does not come loose. If
the bit is not installed properly, it can come loose
during use, which can be dangerous.
6.
Use the bit that matches the screw.
7.
Tightening a screw with the tool at an angle to
that tool can damage the head of the screw and
the proper force will not be transmitted to the
screw. Tighten with this tool lined up straight with
the screw.
8.
Always charge the battery at a temperature of 0
– 40°C.
A temperature of less than 0°C will result in over
charging which is dangerous. The battery cannot
be charged at a temperature greater than 40°C.
The most suitable temperature for charging is that
of 20 – 25°C.
9.
Do not use the charger continuously.
When one charging is completed, leave the charger
for about 15 minutes before the next charging of
battery.
10.
Do not allow foreign matter to enter the hole for
connecting the rechargeable battery.
11.
Never disassemble the rechargeable battery and
charger.
12.
Never short-circuit the rechargeable battery.
Short-circuiting the battery will cause a great
electric current and overheat. It results in burn or
damage to the battery.
13.
Do not dispose of the battery in fire.
If the battery burnt, it may explode.
14.
Bring the battery to the shop from which it was
purchased as soon as the post-charging battery
life becomes too short for practical use. Do not
dispose of the exhausted battery.
15.
Using an exhausted battery will damage the charger.
16.
When drilling in wall, floor or ceiling, check for
buried electric power cord, etc.
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips
with the protection function to stop the output.
In the cases of 1 to 3 described below, when using
this product, even if you are pulling the switch, the
motor may stop. This is not the trouble but the result
of protection function.
1.
When the battery power remaining runs out, the
motor stops.
In such a case, charge it up immediately.
2.
If the tool is overloaded, the motor may stop. In this
case, release the switch of tool and eliminate causes
of overloading. After that, you can use it again.
3.
If the battery is overheated under overload work,
the battery power may stop.
In this case, stop using the battery and let the
battery cool. After that, you can use it again.
Furthermore, please heed the following warning and
caution.
WARNING
In order to prevent any battery leakage, heat generation,
smoke emission, explosion and ignition beforehand,
please be sure to heed the following precautions.
1.
Make sure that swarf and dust do not collect on
the battery.
䡬
During work make sure that swarf and dust do not
fall on the battery.
䡬
Make sure that any swarf and dust falling on the
power tool during work do not collect on the battery.
䡬
Do not store an unused battery in a location exposed
to swarf and dust.
䡬
Before storing a battery, remove any swarf and
dust that may adhere to it and do not store it
together with metal parts (screws, nails, etc.).
2.
Do not pierce battery with a sharp object such
as a nail, strike with a hammer, step on, throw
or subject the battery to severe physical shock.
3.
Do not use an apparently damaged or deformed
battery.
4.
Do not use the battery in reverse polarity.
5.
Do not connect directly to an electrical outlets or
car cigarette lighter sockets.
6.
Do not use the battery for a purpose other than
those specified.
7.
If the battery charging fails to complete even
when a specified recharging time has elapsed,
immediately stop further recharging.
8.
Do not put or subject the battery to high
temperatures or high pressure such as into a
microwave oven, dryer, or high pressure container.
9.
Keep away from fire immediately when leakage
or foul odor are detected.
10.
Do not use in a location where strong static
electricity generates.
11.
If there is battery leakage, foul odor, heat
generated, discolored or deformed, or in any way
appears abnormal during use, recharging or
storage, immediately remove it from the equipment
or battery charger, and stop use.
01Eng_WM10DBL_EE
12/7/11, 9:03 AM
8
